C8051F902-GU Silicon Laboratories Inc, C8051F902-GU Datasheet - Page 88

• Manufacturer Part Number: C8051F902-GU
• Description: IC MCU 8BIT 8KB FLASH 24QSOP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F902-GU

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 24-QSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 15x10/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Ram Size: 768 B
• Interface Type: UART
• Maximum Clock Frequency: 25 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F912DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit
• Package: 24QSOP
• Device Core: 8051
• Family Name: C8051F90x
• Maximum Speed: 25 MHz
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1849-5

C8051F91x-C8051F90x
7.
C8051F91x-C8051F90x devices include two on-chip programmable voltage comparators: Comparator 0
(CPT0) is shown in Figure 7.1; Comparator 1 (CPT1) is shown in Figure 7.2. The two comparators operate
identically, but may differ in their ability to be used as reset or wake-up sources. See the Reset Sources
chapter and the Power Management chapter for details on reset sources and low power mode wake-up
sources, respectively.
The Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a digital synchronous “latched” output (CP0, CP1), or
a digital asynchronous “raw” output (CP0A, CP1A). The asynchronous CP0A signal is available even when
the system clock is not active. This allows the Comparator to operate and generate an output when the
device is in some low power modes.
7.1.
Each Comparator performs an analog comparison of the voltage levels at its positive (CP0+ or CP1+) and
negative (CP0- or CP1-) input. Both comparators support multiple port pin inputs multiplexed to their
positive and negative comparator inputs using analog input multiplexers. The analog input multiplexers are
completely under software control and configured using SFR registers. See Section “7.6. Comparator0 and
Comparator1 Analog Multiplexers” on page 95 for details on how to select and configure Comparator
inputs.
Important Note About Comparator Inputs: The Port pins selected as Comparator inputs should be
configured as analog inputs and skipped by the Crossbar. See the Port I/O chapter for more details on how
to configure Port I/O pins as Analog Inputs. The Comparator may also be used to compare the logic level
of digital signals, however, Port I/O pins configured as digital inputs must be driven to a valid logic state
(HIGH or LOW) to avoid increased power consumption.
88
Comparators
Analog Input Multiplexer
Px.x
Px.x
Px.x
Px.x
Comparator Inputs
Figure 7.1. Comparator 0 Functional Block Diagram
CP0HYN1
CP0HYN0
CP0HYP1
CP0HYP0
CP0OUT
CP0RIF
CP0FIF
CP0EN
CP0 +
CP0 -
+
-
Rev. 1.0
VDD
GND
Decision
Reset
CPT0MD
Tree
(ASYNCHRONOUS)
(SYNCHRONIZER)
D
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Rising-edge
CP0
Crossbar
Interrupt
Logic
Falling-edge
Interrupt
CP0
CP0A
CP0
CP0