SAM7X128 Atmel Corporation, SAM7X128 Datasheet - Page 659

• Manufacturer Part Number: SAM7X128
• Manufacturer: Atmel Corporation

Specifications of SAM7X128

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.5.4
41.5.4.1
41.5.4.2
41.5.5
41.5.5.1
41.5.5.2
41.5.5.3
41.5.5.4
6120I–ATARM–06-Apr-11
Peripheral Input/Output (PIO)
Pulse Width Modulation Controller (PWM)
PIO: Electrical Characteristics on NRST, PA0-PA30 and PB0-PB26
PWM: Counter Start Value
PWM: Behavior of CHIDx Status Bits in the PWM_SR Register
PIO: Drive Low NRST, PA0-PA30 and PB0-PB26
PWM: Update when PWM_CCNTx = 0 or 1
PWM: Update when PWM_CPRDx = 0
When NRST or PA0 - PA30 or PB0 - PB26 are set as digital inputs with pull-up enabled, the volt-
age of the I/O stabilizes at VPull-up.
Vpull-up
This condition causes a leakage through VDDIO. This leakage is 45 µA per pad in worst case at
3.3 V.
I Leakage
It is recommended to use an external pull-up if needed.
When NRST or PA0 - PA30 or PB0 - PB26 are set as digital inputs with pull-up enabled, driving
the I/O with an output impedance higher than 500 ohms may not drive the I/O to a logical zero.
Output impedance must be lower than 500 ohms.
If the Channel Counter Register value is 0 or 1, the Channel Period Register or Channel Duty
Cycle Register is directly modified when writing the Channel Update Register.
Check the Channel Counter Register before writing the update register.
When Channel Period Register equals 0, the period update is not operational.
Do not write 0 in the period register.
In left aligned mode, the first start value of the counter is 0. For the other periods, the counter
starts at 1.
None.
Erratic behavior of the CHIDx status bit in the PWM_SR Register. When a channel is disabled
by writing in the PWM_DIS Register just after enabling it (before completion of a Clock Period of
VPull-up Min
VDDIO - 0.65 V
Parameter
I Leakage at 3,3V
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
VPull-up Max
VDDIO - 0.45 V
Typ
2.5
µA
Max
45
µA
SAM7X512/256/128
659