PIC18LF25J11-I/SO Microchip Technology, PIC18LF25J11-I/SO Datasheet - Page 289

• Manufacturer Part Number: PIC18LF25J11-I/SO
• Description: IC PIC MCU FLASH 32K 2V 28-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF25J11-I/SO

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3776Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• No. Of Pwm: RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REGISTER 18-8:
REGISTER 18-9:
© 2009 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5-2
bit 1
bit 0
Note 1:
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-0
Note 1:
GCEN
R/W-0
R/W-1
MSK7
2:
2:
If the I
(or writes to the SSPxBUF are disabled).
This bit is unimplemented in I
This register shares the same SFR address as SSPxADD and is only addressable in select MSSP
operating modes. See Section 18.5.3.4 “7-Bit Address Masking Mode” for more details.
MSK0 is not used as a mask bit in 7-bit addressing.
GCEN: General Call Enable bit (Slave mode only)
1 = Enables interrupt when a general call address (0000h) is received in the SSPxSR
0 = General call address disabled
ACKSTAT: Acknowledge Status bit
Unused in Slave mode.
ADMSK<5:2>: Slave Address Mask Select bits (5-Bit Address Masking)
1 = Masking of corresponding bits of SSPxADD enabled
0 = Masking of corresponding bits of SSPxADD disabled
ADMSK1: Slave Address Least Significant bit(s) Mask Select bit
In 7-Bit Addressing mode:
1 = Masking of SSPxADD<1> only enabled
0 = Masking of SSPxADD<1> only disabled
In 10-Bit Addressing mode:
1 = Masking of SSPxADD<1:0> enabled
0 = Masking of SSPxADD<1:0> disabled
SEN: Start Condition Enable/Stretch Enable bit
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)
0 = Clock stretching is disabled
MSK<7:0>: Slave Address Mask Select bits
1 = Masking of corresponding bit of SSPxADD enabled
0 = Masking of corresponding bit of SSPxADD disabled
ACKSTAT
2
R/W-0
C module is active, these bits may not be set (no spooling) and the SSPxBUF may not be written
R/W-1
MSK6
SSPxCON2: MSSPx CONTROL REGISTER 2 – I
(ACCESS FC5h/F71h)
SSPxMSK: I
(ACCESS FC8h/F74h)
(2)
W = Writable bit
‘1’ = Bit is set
W = Writable bit
‘1’ = Bit is set
ADMSK5
R/W-0
R/W-1
MSK5
2
C™ SLAVE ADDRESS MASK REGISTER – 7-BIT MASKING MODE
2
C Slave mode.
ADMSK4
R/W-0
(1)
R/W-1
MSK4
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
ADMSK3
PIC18F46J11 FAMILY
(1)
R/W-0
R/W-1
MSK3
ADMSK2
R/W-0
R/W-1
MSK2
2
C™ SLAVE MODE
x = Bit is unknown
x = Bit is unknown
ADMSK1
R/W-0
R/W-1
MSK1
DS39932C-page 289
MSK0
SEN
R/W-0
R/W-1
(1)
(2)
bit 0
bit 0