PIC18LF25J11-I/SO Microchip Technology, PIC18LF25J11-I/SO Datasheet - Page 324

• Manufacturer Part Number: PIC18LF25J11-I/SO
• Description: IC PIC MCU FLASH 32K 2V 28-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF25J11-I/SO

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3776Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• No. Of Pwm: RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F46J11 FAMILY
REGISTER 19-3:
DS39932C-page 324
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
ABDOVF
R/W-0
ABDOVF: Auto-Baud Acquisition Rollover Status bit
1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode (must be cleared in software)
0 = No BRG rollover has occurred
RCIDL: Receive Operation Idle Status bit
1 = Receive operation is Idle
0 = Receive operation is active
RXDTP: Data/Receive Polarity Select bit
Asynchronous mode:
1 = Receive data (RXx) is inverted (active-low)
0 = Receive data (RXx) is not inverted (active-high)
Synchronous mode:
1 = Data (DTx) is inverted (active-low)
0 = Data (DTx) is not inverted (active-high)
TXCKP: Synchronous Clock Polarity Select bit
Asynchronous mode:
1 = Idle state for transmit (TXx) is a low level
0 = Idle state for transmit (TXx) is a high level
Synchronous mode:
1 = Idle state for clock (CKx) is a high level
0 = Idle state for clock (CKx) is a low level
BRG16: 16-Bit Baud Rate Register Enable bit
1 = 16-bit Baud Rate Generator – SPBRGHx and SPBRGx
0 = 8-bit Baud Rate Generator – SPBRGx only (Compatible mode), SPBRGHx value ignored
Unimplemented: Read as ‘0’
WUE: Wake-up Enable bit
Asynchronous mode:
1 = EUSART will continue to sample the RXx pin – interrupt generated on falling edge; bit cleared in
0 = RXx pin not monitored or rising edge detected
Synchronous mode:
Unused in this mode.
ABDEN: Auto-Baud Detect Enable bit
Asynchronous mode:
1 = Enable baud rate measurement on the next character; requires reception of a Sync field (55h);
0 = Baud rate measurement disabled or completed
Synchronous mode:
Unused in this mode.
RCIDL
hardware on following rising edge
cleared in hardware upon completion
R-1
BAUDCONx: BAUD RATE CONTROL REGISTER (ACCESS F7Eh/F7Ch)
W = Writable bit
‘1’ = Bit is set
RXDTP
R/W-0
TXCKP
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
BRG16
R/W-0
U-0
—
© 2009 Microchip Technology Inc.
x = Bit is unknown
R/W-0
WUE
ABDEN
R/W-0
bit 0