ST72F324BJ6T6 STMicroelectronics, ST72F324BJ6T6 Datasheet - Page 195

• Manufacturer Part Number: ST72F324BJ6T6
• Description: IC MCU 8BIT 32K FLASH 44-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324BJ6T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5590

ST72324B-Auto
16
Revision history
Table 123. Document revision history
23-May-2007
23-Jul-2007
Date
Revision
1
2
Initial release
Replaced ST72324B-Auto with ST72324Bxx-Auto in document title on
cover page.
1 analog peripheral (low current coupling) on page
input ports’ with ‘12 input ports’
Table 1: Device summary on page
Added
datasheets on page
Figure 2: 44-pin LQFP package pinout on page
numbers for pins 18 and 20 (port numbers were hidden due to formatting
error)
Table 2: Device pin description on page
- replaced V
- modified
Section 5.3.4: Condition Code register (CC) on page
with ISPRx
Section 9.5.1: I/O port implementation on page
tables:
- Standard ports PA5:4, PC7:0, PD5:0, PE1:0, PF7:6, 4
- Interrupt ports PB4, PB2:0, PF2:0 (with pull-up)
- Interrupt ports PA3, PB3 (without pull-up)
-
exist in
Section 12.6.3: Crystal and ceramic resonator
tables
devices)
and ROM devices)
oscillators on page
Table 96: OSCRANGE selection for typical resonators on page
Deleted footnote detailing SMD and LEAD which was linked to
‘Reference’ column header
Table 102: EMI emissions on page
- added LQFP32 package to all listed devices
- changed values for 32 Kbyte ROM devices
Table 105: General characteristics on page
- modified
- modified
Figure 76: RESET pin protection when LVD is enabled(1)(2)(3)(4)(5)(6)
on page
formatting error
Table 111: 10-bit ADC characteristics on page
leakage parameter and added
Table 112: ADC accuracy on page
- added conditions to total unadjusted error, to offset error and to gain
error
- modified
True open drain ports PA7:6
Doc ID13466 Rev 4
Crystal and ceramic resonator oscillators (8/16K Flash and ROM
Section 1.2: Differences between ST72324B-Auto and ST72324B
Table 32: Port
168: Replaced ‘MW’ with ‘M ohm’ in footnotes to correct
and
Note
Note
Note
Note 2
DDA
Crystal and ceramic resonator oscillators (32 Kbyte Flash
2
5
6
with V
with single
156
16
configuration)
REF
in
Note
(configurations in these four tables already
Table 95: Crystal and ceramic resonator
Note
Changes
1: Corrected order of listed packages
1
175:
161:
2
18:
163:
172: Modified input current
oscillators: Replaced two
65: Removed following
17: Displayed port
1: Replaced ‘12 robust
29: Replaced IxSPR
Revision history
157:
195/198