ST72F324BJ6T6 STMicroelectronics, ST72F324BJ6T6 Datasheet - Page 53

• Manufacturer Part Number: ST72F324BJ6T6
• Description: IC MCU 8BIT 32K FLASH 44-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324BJ6T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5590

ST72324B-Auto
8.3
Figure 22. Slow mode clock transitions
Wait mode
Wait mode places the MCU in a low power consumption mode by stopping the CPU.
This power saving mode is selected by calling the ‘WFI’ instruction.
All peripherals remain active. During Wait mode, the I[1:0] bits of the CC register are forced
to ‘10’, to enable all interrupts. All other registers and memory remain unchanged. The MCU
remains in Wait mode until an interrupt or reset occurs, whereupon the Program Counter
branches to the starting address of the interrupt or reset service routine. The MCU will
remain in Wait mode until a reset or an interrupt occurs, causing it to wake up. Refer to
Figure
Figure 23. Wait mode flowchart
1. Before servicing an interrupt, the CC register is pushed on the stack. The I[1:0] bits of the CC register are
set to the current software priority level of the interrupt routine and recovered when the CC register is
popped.
23.
CP1:0
SMS
f
f
CPU
OSC2
N
WFI instruction
Doc ID13466 Rev 4
f
OSC2
Interrupt
00
Y
New Slow
frequency
request
/2
01
256 or 4096 CPU clock
f
Oscillator
Peripherals
CPU
I[1:0] bits
Oscillator
Peripherals
CPU
I[1:0] bits
Oscillator
Peripherals
CPU
I[1:0] bits
N
OSC2
Fetch reset vector
or service interrupt
Normal Run mode
/4
cycle delay
Y
Reset
f
OSC2
XX
on
on
on
10
10
on
on
off
on
off
on
(1)
request
Power saving modes
53/198