C8051T606-ZM Silicon Laboratories Inc, C8051T606-ZM Datasheet - Page 76
![IC 8051 MCU 1.5K-EEPROM 10-QFN](/photos/12/15/121567/10-qfn_pkg_sml.jpg)
C8051T606-ZM
Manufacturer Part Number
C8051T606-ZM
Description
IC 8051 MCU 1.5K-EEPROM 10-QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051T60xr
Specifications of C8051T606-ZM
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1.5KB (1.5K x 8)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
10-QFN
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
I2C, UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
6
Number Of Timers
3
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051T606DK
Minimum Operating Temperature
- 40 C
Eeprom Size
-
Data Converters
-
For Use With
336-1668 - CARD DAUGHTER QFN10 SOCKET336-1667 - CARD DAUGHTER MSOP SOCKET336-1666 - KIT DEVELOPMENT FOR C8051T606336-1404 - KIT DEV FOR C8051T60X MCU'S
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Details
Other names
336-1663-2
C8051T606-ZMR
C8051T606-ZMR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T606-ZMR
Manufacturer:
STM
Quantity:
4 037
C8051T600/1/2/3/4/5/6
15.2.1.1. General Purpose Registers
The lower 32 bytes of data memory, locations 0x00 through 0x1F, may be addressed as four banks of gen-
eral-purpose registers. Each bank consists of eight byte-wide registers designated R0 through R7. Only
one of these banks may be enabled at a time. Two bits in the program status word, RS0 (PSW.3) and RS1
(PSW.4), select the active register bank (see description of the PSW in SFR Definition 14.6). This allows
fast context switching when entering subroutines and interrupt service routines. Indirect addressing modes
use registers R0 and R1 as index registers.
15.2.1.2. Bit Addressable Locations
In addition to direct access to data memory organized as bytes, the sixteen data memory locations at 0x20
through 0x2F are also accessible as 128 individually addressable bits. Each bit has a bit address from
0x00 to 0x7F. Bit 0 of the byte at 0x20 has bit address 0x00 while bit 7 of the byte at 0x20 has bit address
0x07. Bit 7 of the byte at 0x2F has bit address 0x7F. A bit access is distinguished from a full byte access by
the type of instruction used (bit source or destination operands as opposed to a byte source or destina-
tion).
The MCS-51™ assembly language allows an alternate notation for bit addressing of the form XX.B where
XX is the byte address and B is the bit position within the byte. For example, the instruction:
MOV
C, 22.3h
moves the Boolean value at 0x13 (bit 3 of the byte at location 0x22) into the Carry flag.
15.2.1.3. Stack
A programmer's stack can be located anywhere in the internal data memory. The stack area is designated
using the Stack Pointer (SP) SFR. The SP will point to the last location used. The next value pushed on the
stack is placed at SP+1 and then SP is incremented. A reset initializes the stack pointer to location 0x07.
Therefore, the first value pushed on the stack is placed at location 0x08, which is also the first register (R0)
of register bank 1. Thus, if more than one register bank is to be used, the SP should be initialized to a loca-
tion in the data memory not being used for data storage. The stack depth can extend up to the full RAM
area.
76
Rev. 1.2