C8051T606-ZM Silicon Laboratories Inc, C8051T606-ZM Datasheet - Page 90
![IC 8051 MCU 1.5K-EEPROM 10-QFN](/photos/12/15/121567/10-qfn_pkg_sml.jpg)
C8051T606-ZM
Manufacturer Part Number
C8051T606-ZM
Description
IC 8051 MCU 1.5K-EEPROM 10-QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051T60xr
Specifications of C8051T606-ZM
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1.5KB (1.5K x 8)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
10-QFN
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
I2C, UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
6
Number Of Timers
3
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051T606DK
Minimum Operating Temperature
- 40 C
Eeprom Size
-
Data Converters
-
For Use With
336-1668 - CARD DAUGHTER QFN10 SOCKET336-1667 - CARD DAUGHTER MSOP SOCKET336-1666 - KIT DEVELOPMENT FOR C8051T606336-1404 - KIT DEV FOR C8051T60X MCU'S
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Details
Other names
336-1663-2
C8051T606-ZMR
C8051T606-ZMR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T606-ZMR
Manufacturer:
STM
Quantity:
4 037
C8051T600/1/2/3/4/5/6
18.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the controller core to enter stop mode as soon as the
instruction that sets the bit completes execution. In stop mode the internal oscillator, CPU, and all digital
peripherals are stopped; the state of the external oscillator circuit is not affected. Each analog peripheral
(including the external oscillator circuit) may be shut down individually prior to entering stop mode. Stop
mode can only be terminated by an internal or external reset. On reset, the device performs the normal
reset sequence and begins program execution at address 0x0000.
If enabled, the missing clock detector will cause an internal reset and thereby terminate the stop mode.
The missing clock detector should be disabled if the CPU is to be put to in stop mode for longer than the
MCD timeout.
By default, when in stop mode the internal regulator is still active. However, the regulator can be config-
ured to shut down while in stop mode to save power. To shut down the regulator in stop mode, the
STOPCF bit in register REG0CN should be set to 1 prior to setting the STOP bit (see SFR Definition 12.1).
If the regulator is shut down using the STOPCF bit, only the RST pin or a full power cycle are capable of
resetting the device.
90
Rev. 1.2