C8051T606-ZM Silicon Laboratories Inc, C8051T606-ZM Datasheet - Page 81
![IC 8051 MCU 1.5K-EEPROM 10-QFN](/photos/12/15/121567/10-qfn_pkg_sml.jpg)
C8051T606-ZM
Manufacturer Part Number
C8051T606-ZM
Description
IC 8051 MCU 1.5K-EEPROM 10-QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051T60xr
Specifications of C8051T606-ZM
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1.5KB (1.5K x 8)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
10-QFN
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
I2C, UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
6
Number Of Timers
3
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051T606DK
Minimum Operating Temperature
- 40 C
Eeprom Size
-
Data Converters
-
For Use With
336-1668 - CARD DAUGHTER QFN10 SOCKET336-1667 - CARD DAUGHTER MSOP SOCKET336-1666 - KIT DEVELOPMENT FOR C8051T606336-1404 - KIT DEV FOR C8051T60X MCU'S
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Details
Other names
336-1663-2
C8051T606-ZMR
C8051T606-ZMR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T606-ZMR
Manufacturer:
STM
Quantity:
4 037
C8051T600/1/2/3/4/5/6
17.1. MCU Interrupt Sources and Vectors
The C8051T600/1/2/3/4/5/6 MCUs support 12 interrupt sources. Software can simulate an interrupt by set-
ting an interrupt-pending flag to logic 1. If interrupts are enabled for the flag, an interrupt request will be
generated and the CPU will vector to the ISR address associated with the interrupt-pending flag. MCU
interrupt sources, associated vector addresses, priority order and control bits are summarized in
Table 17.1. Refer to the datasheet section associated with a particular on-chip peripheral for information
regarding valid interrupt conditions for the peripheral and the behavior of its interrupt-pending flag(s).
17.1.1. Interrupt Priorities
Each interrupt source can be individually programmed to one of two priority levels: low or high. A low prior-
ity interrupt service routine can be preempted by a high priority interrupt. A high priority interrupt cannot be
preempted. Each interrupt has an associated interrupt priority bit in an SFR (IP or EIP1) used to configure
its priority level. Low priority is the default. If two interrupts are recognized simultaneously, the interrupt with
the higher priority is serviced first. If both interrupts have the same priority level, a fixed priority order is
used to arbitrate, given in Table 17.1.
17.1.2. Interrupt Latency
Interrupt response time depends on the state of the CPU when the interrupt occurs. Pending interrupts are
sampled and priority decoded each system clock cycle. Therefore, the fastest possible response time is 5
system clock cycles: 1 clock cycle to detect the interrupt and 4 clock cycles to complete the LCALL to the
ISR. If an interrupt is pending when a RETI is executed, a single instruction is executed before an LCALL
is made to service the pending interrupt. Therefore, the maximum response time for an interrupt (when no
other interrupt is currently being serviced or the new interrupt is of greater priority) occurs when the CPU is
performing an RETI instruction followed by a DIV as the next instruction. In this case, the response time is
18 system clock cycles: 1 clock cycle to detect the interrupt, 5 clock cycles to execute the RETI, 8 clock
cycles to complete the DIV instruction and 4 clock cycles to execute the LCALL to the ISR. If the CPU is
executing an ISR for an interrupt with equal or higher priority, the new interrupt will not be serviced until the
current ISR completes, including the RETI and following instruction.
Rev. 1.2
81