M30833FJGP#U5 Renesas Electronics America, M30833FJGP#U5 Datasheet - Page 432

• Manufacturer Part Number: M30833FJGP#U5
• Description: IC M32C/83 MCU FLASH 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M30833FJGP#U5

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 31K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-LQFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R
R
M
e
E
3
. v
J
Figure 25.11 Full Status Check and Handling Procedure for Each Error
2
0
1
9
C
3 .
B
8 /
0
1
3
0
3
J
G
Write command code
4
a
NOTE: When any of the SR5 to SR3 bits are set to "1", the page program, block erase, erase all unlocked block and lock bit program
Read even address
0 -
in user ROM area
n
o r
3 .
1
u
Completed
, 1
3
p
commands cannot be accepted.
Execute the clear status register command before each command.
"xx70
SR5=0 ?
SR4=0 ?
SR3=0 ?
1
SR4=1
SR5=1
Start
2
(
and
M
0
?
0
16
NO
YES
YES
YES
3
6
2
"
C
Page 407
8 /
, 3
YES
NO
NO
NO
M
3
2
C
Command sequence
f o
Excessive write error
8 /
Program error
4
Erase error
3
8
) T
8
error
(1) Execute the clear status register command and set the SR4 bit to "0".
(2) Execute the read lock bit status command, and set the FMR02 bit to "1" if
(3) Execute the page program command again.
(1) Execute the clear status register command and set the SR4 bit to "0".
(2) Set the FMR02 bit to "1".
(3) Execute the block erase command to erase the block where the error
(4) Execute the lock bit program command again.
[When a lock bit program operation is executed]
[When a page program operation is executed]
(1) Execute the clear status register command and set the SR5 bit to "0".
(2) Execute the lock bit read status command, and set the FMR02 bit to "1" if
(3) Execute the block erase or erase all unlocked block command again.
(1) Execute the clear status register command and set the SR3 bit to "0".
(2) Execute the block erase command to erase the block where the error
(3) Execute the page program command again.
(1) Execute the clear status register command,
(2) Execute the correct command again.
NOTE: If similar error occurs, that block cannot be used.
the lock bit in the block where the error occurred is set to "0" (locked) .
NOTE: If similar error occurs, that block cannot be used.
occurred.
the lock bit in the block where the error occurred is set to "0" (locked).
NOTE: If similar error occurs, that block cannot be used.
occurred.
NOTE: If similar error occurs, that block cannot be used.
and set the SR4 and SR5 bits to "0".
NOTE: If similar error occurs, that block cannot be used.
If the lock bit is set to "1" (unlocked) in (2) above, that block cannot
be used.
If the lock bit is set to "1" (unlocked) in (2) above, that block cannot
be used.
25. Flash Memory Version