AT91SAM7X128B-AU Atmel, AT91SAM7X128B-AU Datasheet - Page 281

• Manufacturer Part Number: AT91SAM7X128B-AU
• Description: IC MCU 128KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X128B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: JTAG, SPI, UART
• Maximum Clock Frequency: 55 MHz
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7X-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

29. Two-wire Interface (TWI)
29.1
29.2
6120I–ATARM–06-Apr-11
Overview
Block Diagram
The Two-wire Interface (TWI) interconnects components on a unique two-wire bus, made up of
one clock line and one data line with speeds of up to 400 Kbits per second, based on a byte-ori-
ented transfer format. It can be used with any Atmel Two-wire Interface bus Serial EEPROM and
I²C compatible device such as Real Time Clock (RTC), Dot Matrix/Graphic LCD Controllers and
Temperature Sensor, to name but a few. The TWI is programmable as master transmitter or
master receiver with sequential or single-byte access. A configurable baud rate generator per-
mits the output data rate to be adapted to a wide range of core clock frequencies. Below,
29-1
Table 29-1.
Notes:
Figure 29-1. Block Diagram
I2C Standard
Standard Mode Speed (100 KHz)
Fast Mode Speed (400 KHz)
7 or 10 bits Slave Addressing
START BYTE
Repeated Start (Sr) Condition
ACK and NACK Management
Slope control and input filtering (Fast mode)
Clock strectching
lists the compatibility level of the Atmel Two-wire Interface and a full I2C compatible device.
1. START + b000000001 + Ack + Sr
2. A repeated start condition is only supported in Master Receiver mode. See
”Internal Address” on page 286
(1)
Atmel TWI compatibility with i2C Standard
PMC
APB Bridge
MCK
SAM7X512/256/128 Preliminary
Two-wire
Interface
Atmel TWI
Supported
Supported
Supported
Not Supported
Not Fully Supported
Supported
Not Supported
Supported
Interrupt
TWI
PIO
AIC
(2)
TWCK
TWD
Section 29.5.5
Table
281