F272-BAGE-T-TR STMicroelectronics, F272-BAGE-T-TR Datasheet - Page 150

• Manufacturer Part Number: F272-BAGE-T-TR
• Description: MCU 16BIT 256K FLASH 144-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of F272-BAGE-T-TR

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: ASC, CAN, EBI/EMI, I²C, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-TQFP, 144-VQFP
• Data Bus Width: 16 bit
• Data Ram Size: 20 KB
• Interface Type: ASC, CAN, I2C, SSC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

Electrical characteristics
24.8.7
24.8.8
Table 69.
150/182
1
1
1
1
0
(P0H.7-5)
P0.15-13
1
1
0
0
1
1
0
1
0
1
an external clock failure occurs, then the watchdog counter overflows (after 16 PLL clock
cycles).
The CPU clock signal will be switched to the PLL free-running clock signal, and the oscillator
watchdog Interrupt Request is flagged. The CPU clock will not switch back to the external
clock even if a valid external clock exits on XTAL1 pin. Only a hardware reset (or
bidirectional Software / Watchdog reset) can switch the CPU clock source back to direct
clock input.
When the OWD is disabled, the CPU clock is always the external oscillator clock (in Direct
Drive or Prescaler Operation) and the PLL is switched off to decrease consumption supply
current.
Phase Locked Loop (PLL)
For all other combinations of pins P0.15-13 (P0H.7-5) during reset the on-chip phase locked
loop is enabled and it provides the CPU clock (see
frequency by the factor F which is selected via the combination of pins P0.15-13 (f
f
the input clock. This synchronization is done smoothly, so the CPU clock frequency does not
change abruptly.
Due to this adaptation to the input clock the frequency of f
locked to f
individual TCLs.
The timings listed in the AC Characteristics that refer to TCLs therefore must be calculated
using the minimum TCL that is possible under the respective circumstances.
The real minimum value for TCL depends on the jitter of the PLL. The PLL tunes f
keep it locked on f
one TCL period.
This is especially important for bus cycles using wait states and e.g. for the operation of
timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train
generation or measurement, lower Baud rates, etc.) the deviation caused by the PLL jitter is
negligible. Refer to next
Voltage Controlled Oscillator
The ST10F272 implements a PLL which combines different levels of frequency dividers with
a Voltage Controlled Oscillator (VCO) working as frequency multiplier. In the following table,
a detailed summary of the internal settings and VCO frequency is reported.
Internal PLL divider mechanism
XTAL
5.3 to 10.6MHz
6.4 to 12MHz
Frequency
1 to 64MHz
4 to 8MHz
4 to 8MHz
x F). With every F’th transition of f
XTAL
XTAL
. The slight variation causes a jitter of f
1)
1)
XTAL
Prescaler
F
F
F
F
XTAL
XTAL
XTAL
XTAL
Input
. The relative deviation of TCL is the maximum when it is referred to
–
Section 24.8.9: PLL Jitter
/ 4
/ 4
/ 4
/ 4
Multiply by
64
48
64
40
PLL bypassed
XTAL
PLL
the PLL circuit synchronizes the CPU clock to
Divide by
4
4
2
2
for more details.
Table
CPU
68). The PLL multiplies the input
which also effects the duration of
CPU
Prescaler
Output
is constantly adjusted so it is
–
–
–
–
–
ST10F272B/ST10F272E
CPU Frequency
f
CPU
F
F
F
F
F
XTAL
XTAL
XTAL
XTAL
XTAL
= f
CPU
XTAL
CPU
x 4
x 3
x 8
x 5
x 1
to
x F
=