MC9S08GT16ACFBE Freescale Semiconductor, MC9S08GT16ACFBE Datasheet - Page 35

• Manufacturer Part Number: MC9S08GT16ACFBE
• Description: IC MCU 16K FLASH 2K RAM 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT16ACFBE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 36
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PQFP
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

3.5
One of three stop modes is entered upon execution of a STOP instruction when the STOPE bit in the
system option register is set. In all stop modes, all internal clocks are halted. If the STOPE bit is not set
when the CPU executes a STOP instruction, the MCU will not enter any of the stop modes and an illegal
opcode reset is forced. The stop modes are selected by setting the appropriate bits in SPMSC2.
Table 3-1
1
2
3.5.1
The stop1 mode provides the lowest possible standby power consumption by causing the internal circuitry
of the MCU to be powered down. Stop1 can be entered only if the LVD circuit is not enabled in stop modes
(either LVDE or LVDSE not set).
When the MCU is in stop1 mode, all internal circuits that are powered from the voltage regulator are turned
off. The voltage regulator is in a low-power standby state, as is the ATD.
Exit from stop1 is performed by asserting either of the wake-up pins on the MCU: RESET or IRQ. IRQ is
always an active low input when the MCU is in stop1, regardless of how it was configured before entering
stop1.
Entering stop1 mode automatically asserts LVD. Stop1 cannot be exited until V
must rise above the LVI rearm voltage).
Upon wake-up from stop1 mode, the MCU will start up as from a power-on reset (POR). The CPU will
take the reset vector.
3.5.2
The stop2 mode provides very low standby power consumption and maintains the contents of RAM and
the current state of all of the I/O pins. Stop2 can be entered only if the LVD circuit is not enabled in stop
modes (either LVDE or LVDSE not set).
Freescale Semiconductor
Mode
Stop1
Stop2
Stop3
Either ATD stop mode or power-down mode depending on the state of ATDPU.
Crystal oscillator can be configured to run in stop3. Please see the ICG registers.
Stop Modes
summarizes the behavior of the MCU in each of the stop modes.
PDC
Stop1 Mode
Stop2 Mode
1
1
0
PPDC
Don’t
care
0
1
CPU, Digital
Peripherals,
Standby
FLASH
Off
Off
MC9S08GT16A/GT8A Data Sheet, Rev. 1
Table 3-1. Stop Mode Behavior
Standby
Standby
RAM
Off
ICG
Off
Off
Off
2
Disabled
Disabled
Disabled
ATD
1
Regulator
Standby
Standby
Off
DD
> V
I/O Pins
States
States
Reset
held
held
LVDH/L
Modes of Operation
Optionally on
Optionally on
rising (V
RTI
Off
DD
35