MCHC908GR8AMFAE Freescale Semiconductor, MCHC908GR8AMFAE Datasheet - Page 225

IC MCU 8K FLASH 8MHZ 32-LQFP

MCHC908GR8AMFAE

Manufacturer Part Number
MCHC908GR8AMFAE
Description
IC MCU 8K FLASH 8MHZ 32-LQFP
Manufacturer
Freescale Semiconductor
Series
HC08r
Datasheet

Specifications of MCHC908GR8AMFAE

Core Processor
HC08
Core Size
8-Bit
Speed
8MHz
Connectivity
SCI, SPI
Peripherals
LVD, POR, PWM
Number Of I /o
21
Program Memory Size
7.5KB (7.5K x 8)
Program Memory Type
FLASH
Ram Size
384 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 6x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
32-LQFP
Processor Series
HC08G
Core
HC08
Data Bus Width
8 bit
Data Ram Size
384 B
Interface Type
SCI, SPI
Maximum Clock Frequency
8.2 MHz
Number Of Programmable I/os
21
Number Of Timers
3
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Development Tools By Supplier
FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
Minimum Operating Temperature
- 40 C
On-chip Adc
8 bit, 6 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
 Details

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCHC908GR8AMFAE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MCHC908GR8AMFAER
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Enter monitor mode with pin configuration shown in
RST latches monitor mode. Once monitor mode is latched, the levels on the port pins except PTA0 can
change.
Once out of reset, the MCU waits for the host to send eight security bytes (see
security bytes, the MCU sends a break signal (10 consecutive 0s) to the host, indicating that it is ready to
receive a command.
18.3.1.1 Normal Monitor Mode
When monitor mode is entered with V
long as V
This condition states that as long as V
V
then the COP will be disabled. In the latter situation, after V
removed from the IRQ pin in the interest of freeing the IRQ for normal functionality in monitor mode.
18.3.1.2 Forced Monitor Mode
If entering monitor mode without high voltage on IRQ, all port B pin requirements and conditions are not
in effect. This is to reduce circuit requirements when performing in-circuit programming.
An external oscillator of 9.8304 MHz is required for a baud rate of 9600, as the internal bus frequency is
automatically set to the external frequency divided by four.
When the forced monitor mode is entered the COP is always disabled regardless of the state of IRQ or
RST.
18.3.1.3 Monitor Vectors
In monitor mode, the MCU uses different vectors for reset, SWI (software interrupt), and break interrupt
than those for user mode. The alternate vectors are in the $FE page instead of the $FF page and allow
code execution from the internal monitor firmware instead of user code.
Table 18-2
Freescale Semiconductor
TST
is applied to RST after the initial reset to get into monitor mode (when V
TST
summarizes the differences between user mode and monitor mode.
User
Monitor
Modes
is applied to either IRQ or RST.
If the reset vector is blank and monitor mode is entered, the chip will see an
additional reset cycle after the initial power-on reset (POR). Once the reset
vector has been programmed, the traditional method of applying a voltage,
V
TST
, to IRQ must be used to enter monitor mode.
Vector High
$FFFE
$FEFE
Reset
MC68HC908GR8A • MC68HC908GR4A Data Sheet, Rev. 5
Vector Low
$FFFF
$FEFF
Reset
Table 18-2. Mode Differences
TST
TST
on IRQ, the computer operating properly (COP) is disabled as
is maintained on the IRQ pin after entering monitor mode, or if
Vector High
$FFFC
$FEFC
Break
NOTE
Table 18-1
Functions
Vector Low
$FEFD
TST
$FFFD
Break
with a power-on reset. The rising edge of
is applied to the RST pin, V
Vector High
$FFFC
$FEFC
SWI
TST
18.3.2
was applied to IRQ),
Vector Low
Monitor Module (MON)
$FEFD
$FFFD
Security). After the
SWI
TST
can be
225

Related parts for MCHC908GR8AMFAE