HD6417760BL200AV Renesas Electronics America, HD6417760BL200AV Datasheet - Page 604
HD6417760BL200AV
Manufacturer Part Number
HD6417760BL200AV
Description
SH4 7760, 17 X17 256BGA, LCDC, U
Manufacturer
Renesas Electronics America
Series
SuperH® SH7750r
Datasheet
1.D6417760BP200ADV.pdf
(1418 pages)
Specifications of HD6417760BL200AV
Core Processor
SH-4
Core Size
32-Bit
Speed
200MHz
Connectivity
Audio Codec, CAN, EBI/EMI, FIFO, I²C, MFI, MMC, SCI, Serial Sound, SIM, SPI, USB
Peripherals
DMA, LCD, POR, WDT
Number Of I /o
69
Program Memory Type
ROMless
Ram Size
48K x 8
Voltage - Supply (vcc/vdd)
1.4 V ~ 1.6 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
256-BGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Program Memory Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HD6417760BL200AV
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
HD6417760BL200AV
Manufacturer:
RENENAS
Quantity:
20 000
- Current page: 604 of 1418
- Download datasheet (9Mb)
(2) Exit from Software Standby Mode
Software standby mode is exited by means of an interrupt (NMI, IRL, IRQ*, or GPIO) or a reset
via the RESET and MRESET pins.
Note: * Software standby mode can be cleared by an IRQ4 or IRQ5 interrupt, but not by an
(a) Exit by interrupt
(b) Exit by reset
(3) Clock Pause Function
In software standby mode, it is possible to stop or change the frequency of the clock input from
the EXTAL pin. This function is used as follows.
(a) Enter software standby mode following the transition procedure described above.
(b) When software standby mode is entered and the LSI's internal clock stops, a low-level signal is
(c) The input clock is stopped, or its frequency changed, after the STATUS1 pin goes low and the
(d) When the frequency is changed, input an NMI interrupt after the change. When the clock is
(e) After the time set in the WDT, clock supply begins inside the LSI, the STATUS1 and
Rev. 2.00 Feb. 12, 2010 Page 520 of 1330
REJ09B0554-0200
A hot start can be performed by means of the on-chip WDT. When an NMI, IRL, IRQ, or
GPIO interrupt is detected, the WDT starts counting. After the count overflows, clocks are
supplied to the entire LSI, software standby mode is exited, and the STATUS1 and STATUS0
pins both go low. Interrupt exception handling is then executed, and the code corresponding to
the interrupt source is set in INTEVT. In standby mode, interrupts are accepted even if the BL
bit in the SR register is 1, and so, if necessary, SPC and SSR should be saved to the stack
before executing the SLEEP instruction.
The phase of the CKIO pin clock output may be unstable immediately after an interrupt is
detected, until software standby mode is exited.
Software standby mode is exited by means of a reset (power-on or manual) via the RESET pin.
The RESET pin should be held low until clock oscillation stabilizes. The internal clock
continues to be output at the CKIO pin.
output at the STATUS1 pin, and a high-level signal at the STATUS0 pin.
STATUS0 pin high.
stopped, input an NMI interrupt after applying the clock.
STATUS0 pins both go low, and operation is resumed from interrupt exception handling.
IRQ6 or IRQ7 interrupt.
Related parts for HD6417760BL200AV
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: