ATMEGA6490-16AI Atmel, ATMEGA6490-16AI Datasheet - Page 327

• Manufacturer Part Number: ATMEGA6490-16AI
• Description: IC AVR MCU FLASH 64K 5V 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA6490-16AI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFPATSTK504 - STARTER KIT AVR EXP MOD 100P LCD
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Table 28-1.
Notes:
2552K–AVR–04/11
Symbol
I
V
I
t
CC
ACLK
ACID
ACIO
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at V
4. Although each I/O port can source more than the test conditions (20 mA at V
5. Typical values at 25°C.
V
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
at V
observed:
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
T
CC
= 5V, 5mA at V
A
= 5V, 5mA at V
= -40°C to 85°C, V
CC
(5)
CC
= 3V for all other ports) under steady state conditions (non-transient), the following must be observed:
= 3V for all other ports) under steady state conditions (non-transient), the following must be
CC
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
WDT disabled, V
V
V
V
Condition
Active 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
V
V
V
= 1.8V to 5.5V (unless otherwise noted) (Continued)
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
Min.
-50
ATmega329/3290/649/6490
CC
= 5V, 10mA at V
CC
= 5V, 10 mA at V
Typ.
0.25
<10
750
500
7
CC
= 3V for Port B and 10mA at
CC
Max.
0.45
1.5
3.5
1.5
5.5
12
15
40
50
= 3V for Port B and 10mA
2
Units
mA
mA
mA
mA
mA
mV
mA
µA
µA
nA
ns
327