XR17C158CV-F Exar Corporation, XR17C158CV-F Datasheet - Page 50

• Manufacturer Part Number: XR17C158CV-F
• Description: IC UART PCI BUS 5V OCTAL 144LQFP
• Manufacturer: Exar Corporation
• Type: Universal PCI Bus Octal UARTr

Specifications of XR17C158CV-F

• Number Of Channels: 8
• Package / Case: 144-LQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 6.25 Mbps
• Supply Voltage (max): 7 V
• Supply Current: 5 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 7 V
• No. Of Channels: 8
• Uart Features: High Performance, Read/Write Burst Operation
• Supply Voltage Range: -0.5V To 7V
• Operating Temperature Range: 0°C To +70°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1287

XR17C158
5V PCI BUS OCTAL UART
Enhanced features are enabled or disabled using this register. Bits 0-3 provide single or dual consecutive
character software flow control selection (see
modes are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note
that whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
EFR[3:0]: Software Flow Control Select
Combinations of software flow control can be selected by programming these bits. See
selections. The XOFF1/XOFF2 characters are transmitted approximately 2 character times after the RX FIFO
level has reached the RX trigger level, irrespective of which trigger table is used (Trigger Tables A-D). The
XON1/XON2 characters are transmitted when the RX FIFO level falls below the next lower trigger level for
Trigger Tables A-C and they are transmitted when the RX FIFO level falls below the (RX trigger level -
hysteresis level) for Trigger Table D. For example, if Trigger Table D is used with an RX trigger level of 56 and
a hysteresis level of 16, the XON1/XON2 characters are sent when the RX FIFO level count falls below 40.
4.8.14
Enhanced Feature Register (EFR) - Read/Write
T
ABLE
FCTR B
17: 16 S
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
IT
-3 FCTR B
ELECTABLE
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
IT
-2 FCTR B
H
YSTERESIS
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
IT
Table
-1 FCTR B
L
EVELS
50
18). When the Xon1 and Xon2 and Xoff1 and Xoff2
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
W
IT
HEN
-0
T
RIGGER
RTS/DTR H
(
CHARACTERS
T
ABLE
± 16
± 24
± 32
± 12
± 20
± 28
± 36
± 40
± 44
± 48
± 52
± 4
± 6
± 8
± 8
0
YSTERESIS
-D
IS
)
S
Table 18
ELECTED
xr
for complete
REV. 1.4.3