EP9315-IBZ Cirrus Logic Inc, EP9315-IBZ Datasheet - Page 714

• Manufacturer Part Number: EP9315-IBZ
• Description: 32-Bit Microcontroller IC
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9315-IBZ

• Controller Family/series: (ARM9)
• Core Size: 32 Bit
• A/d Converter: 12 Bits
• Supply Voltage: 3.3V
• No. Of I/o Pins: 65
• Package / Case: 352-PBGA
• Clock Frequency: 200MHz
• Core Processor: ARM9
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, PCMCIA, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9315A-Z
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1144 - KIT DEVELOPMENT EP9315 ARM9
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 598-1263

23
23-2
Synchronous Serial Port
EP93xx User’s Guide
23.5.1 Enabling SSP Operation
23.3 SSP Functionality
23.4 SSP Pin Multiplex
23.5 Configuring the SSP
The SSP includes a programmable bit rate clock divider and prescaler to generate the serial
output clock SCLKOUT from the input clock SSPCLK. Bit rates are supported to 2MHz and
beyond, subject to choice of frequency for SSPCLK. The maximum bit rate will usually be
determined by peripheral devices.
The SSP operating mode, frame format and size are programmed though the control
registers SSPCR0, SSPCR1.
Three individually maskable interrupt outputs, SSPTXINTR, SSPRXINTR and SSPRORINTR
are generated:
The SSP pins are multiplexed and may be used for the I
setting DeviceCfg.I2SonSSP.
Following reset, the SSP logic is disabled and must be configured when in this state. Control
registers SSPCR0 and SSPCR1 need to be programmed to configure the peripheral as a
master or slave operating under one of the following protocols:
The bit rate, derived from the external SSPCLK, requires the programming of the clock
prescale register SSPCPSR. The following procedure must be used to initialize the SSP
function:
You can either prime the transmit FIFO, by writing up to eight 16-bit values when the SSP is
disabled, or allow the transmit FIFO service request to interrupt the CPU. Once enabled,
transmission or reception of data begins on the transmit (SSPTXD) and receive (SSPRXD)
pins.
• SSPTXINTR requests servicing of the transmit buffer
• SSPRXINTR requests servicing of the receive buffer
• SSPRORINTR indicates an overrun condition in the receive FIFO.
• Motorola SPI
• Texas Instruments SSI
• National Semiconductor.
1. Set the enable bit (SSE) in register SSPCR1.
2. Write the other SSP configuration registers: SSPCR0 and SSPCPSR.
3. Clear the enable bit (SSE) in register SSPCR1.
4. Set the enable bit (SSE) in register SSPCR1.
Copyright 2007 Cirrus Logic
2
S controller instead of SSP by
DS785UM1