ISP1507EBS,518 NXP Semiconductors, ISP1507EBS,518 Datasheet - Page 26

• Manufacturer Part Number: ISP1507EBS,518
• Description: RF Transceiver USB 2.0 ULPI TRNSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1507EBS,518

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Single
• Operating Supply Voltage (typ): 3.3V
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Compliant
• Other names: 935285498518 ISP1507EBS-T

NXP Semiconductors
Table 10.
ISP1507E_ISP1507F_1
Product data sheet
DATA
1 to 0
3 to 2
5 to 4
6
7
Fig 8.
DATA [ 3:0 ]
Name
LINESTATE LINESTATE signals: For a definition of LINESTATE, see
V
RxEvent
ID
ALT_INT
Single and back-to-back RXCMDs from the ISP1507 to the link
CLOCK
BUS
RXCMD byte format
STP
9.5.2.1 Linestate encoding
DIR
NXT
state
Description and value
DATA0 — LINESTATE[0]
DATA1 — LINESTATE[1]
Encoded V
Encoded USB event signals: For an explanation of RxEvent, see
Set to the value of the ID pin.
By default, this signal is not used and is not needed in typical designs. Optionally, the link can
enable the BVALID_RISE and/or BVALID_FALL bits in the PWR_CTRL register (see
Section
with the ALT_INT bit asserted.
The ISP1507 will automatically send an RXCMD whenever there is a change in any of the
RXCMD data fields. The link must be able to accept an RXCMD at any time; including
single RXCMDs, back-to-back RXCMDs, and RXCMDs at any time during USB receive
packets when NXT is LOW. An example is shown in
refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1 .
An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt
condition is removed before exiting.
LINESTATE[1:0] reflects the current state of DP and DM. Whenever the ISP1507 detects
a change in DP or DM, an RXCMD will be sent to the link with the new LINESTATE[1:0]
value. The value given on LINESTATE[1:0] depends on the setting of various registers.
Table 11
peripherals.
which applies to host controllers. Dual-role devices must choose the correct table,
depending on whether it is in peripheral or host mode.
10.1.14). Corresponding changes in BVALID will cause an RXCMD to be sent to the link
turnaround
shows the LINESTATE[1:0] encoding for upstream facing ports, which applies to
BUS
Table 12
voltage state: For an explanation of the V
single RXCMD
RXCMD
shows the LINESTATE[1:0] encoding for downstream facing ports,
Rev. 01 — 28 May 2008
turnaround
turnaround
ISP1507E; ISP1507F
Section
BUS
Figure
back-to-back RXCMDs
RXCMD
state, see
ULPI HS USB OTG transceiver
9.5.2.1.
8. For details and diagrams,
Section
RXCMD
Section
9.5.2.4.
© NXP B.V. 2008. All rights reserved.
turnaround
9.5.2.2.
004aaa760
25 of 78