CS5535-UDCF AMD (ADVANCED MICRO DEVICES), CS5535-UDCF Datasheet - Page 109
![no-image](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__sml.jpg)
CS5535-UDCF
Manufacturer Part Number
CS5535-UDCF
Description
Manufacturer
AMD (ADVANCED MICRO DEVICES)
Datasheet
1.CS5535-UDCF.pdf
(579 pages)
Specifications of CS5535-UDCF
Operating Temperature (min)
0C
Operating Temperature (max)
85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CS5535-UDCF
Manufacturer:
AMD
Quantity:
20 000
- Current page: 109 of 579
- Download datasheet (6Mb)
Programmable Interval Timer
5.7.1
Programming of the 8254 PIT is initiated by first writing one
control word via I/O Address 043h into the PIT Mode Con-
trol Word register. It is followed by writing one or two data
bytes via the I/O address of the intended counter. If the
Control register is loaded once, the counters may be over-
written with different values without accessing the Control
register again. Table 5-11 lists the I/O addresses of the
various registers.
The Control register in the 8254 PIT is write-only, but cer-
tain control information can be determined by the read-
back (read-status) command.
5.7.1.1
To load a counter with new values, a control word needs to
output that defines the intended counter, number and type
of bytes to write, the counting mode and the counting for-
mat. Bits [5:4] of the Control Word register (see Section
6.8.2.7 on page 347) indicate whether low-order or high-
order or both are going to be written. If low-order or high-
order counter byte only is specified to be written, then only
that byte can be read during a read access. According to
bits [5:4] of the Control Word register, one needs to write
either the low-order or the high-order or both into the
counter after passing the control word. If bits [5:4] of the
Control Word register is 11, then a low-order byte needs to
be written first, followed by a high-order byte. For small
counting values or counting values that are multiples of
256, it is sufficient to pass the low-order or high-order
counter byte. Bits [3:1] of the Control Word register define
AMD Geode™ CS5535 Companion Device Data Book
I/O Address
040h
041h
042h
043h
Table 5-11. 8254 PIT Register Ports
Programming the 8254 PIT
Write to the Counters
Control Word
Counter 0
Counter 1
Counter 2
Register
Bits [7:6] = Select counter to latch
7
Figure 5-15. PIT Counter Latch Command Format
6
Access Type
Read / Write
Read / Write
Read/ Write
Write
5
0
4
0
the counting mode of the counter selected by bits [5:4]. Bit
0 of the Control Word register defines the binary or BCD
counting format. The maximum loadable count value is not
FFFFh (binary counting) or 9999 (BCD counting), but 0. On
the next CLK pulse the counter concerned jumps to FFFFh
or 9999. Once the value is decreased to 0 again, it outputs
a signal according to the programmed mode. Therefore,
the value 0 corresponds to 2^16 for binary counting and
10^4 for BCD counting.
Read from the Counters
There are three options for reading a counter in the 8254
PIT:
1)
2)
3)
To read a counter, the third option (Direct Read) should not
be used. The Counter Latch command or Read-back com-
mand should be used to transfer the current state of the
counter into its output latches. One or two successive read
counter instructions for the port address of the counter con-
cerned reads these latches. If only the low-order or high-
order byte was written when the counter was loaded with
the initial counting value, then read the current counting
value of the initially written byte by a single read counter
instruction. If both the low-order and high-order counter
bytes are written previously, then to read the current
counter value, two read counter instructions are needed.
The 8254 PIT returns the low-order byte of the 16-bit
counter with the first read counter instruction, and then the
high-order byte with the second read counter instruction. If
the content of the counter has been transferred once by a
counter latch command into the output latches, then this
value is held there until the CPU executes one or two
counter read instructions, or until the corresponding
counter is reprogrammed. Successive counter latch com-
mands are ignored if the output latches haven’t been read
before. Figure 5-15 shows the format of the control word
for the counter latch command.
3
x
Counter Latch command
Read-back (read-status) command
Direct Read
2
x
1
x
31506B
0
x
109
Related parts for CS5535-UDCF
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![CS5535-UDC](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet:
![AMD-751AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751ACAMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-751](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-751AMD-751-TM System Controller Revision Guide
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-X5-133SFZ](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
AMD-X5-133SFZAm5X86? Microprocessor Family
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8131BLC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
Hyper Transport PCI-X Tunnel
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-8111AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
HyperTransport I/O Hub
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-640AC](/images/manufacturer_photos/0/0/14/advanced_micro_devices_tmb.jpg)
Part Number:
Description:
System Controller
Manufacturer:
Advanced Micro Devices
Datasheet:
![AMD-K6](/images/no-image3.png)
Part Number:
Description:
AMD-K6 Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-K6-2E/400AFR](/images/no-image3.png)
Part Number:
Description:
AMD-K6-2E Embedded Processor
Manufacturer:
AMD [Advanced Micro Devices]
Datasheet:
![AMD-8132BLCT](/images/manufacturer_photos/0/0/44/amd__advanced_micro_devices__tmb.jpg)
Part Number:
Description:
Manufacturer:
AMD (ADVANCED MICRO DEVICES)
Datasheet: