ADSP-21371KSWZ-2B Analog Devices Inc, ADSP-21371KSWZ-2B Datasheet - Page 5

• Manufacturer Part Number: ADSP-21371KSWZ-2B
• Description: IC DSP 32BIT 266MHZ 208-LQFP
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Floating Pointr

Specifications of ADSP-21371KSWZ-2B

• Package / Case: 208-LQFP
• Interface: DAI, DPI
• Operating Temperature: 0°C ~ 70°C
• Clock Rate: 266MHz
• Non-volatile Memory: ROM (512 kB)
• On-chip Ram: 128kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Mounting Type: Surface Mount
• Svhc: No SVHC (18-Jun-2010)
• Base Number: 21371
• Core Frequency Typ: 266MHz
• Dsp Type: Floating Point
• Mmac: 532
• No. Of Pins: 208
• Interface Type: SPI, UART
• Rohs Compliant: Yes
• Operating Temperature Range: 0°C To +70°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Data Register File
Each processing element contains a general-purpose data regis-
ter file. The register files transfer data between the computation
units and the data buses, and store intermediate results. These
10-port, 32-register (16 primary, 16 secondary) register files,
combined with the SHARC’s enhanced Harvard architecture,
allow unconstrained data flow between computation units and
internal memory. The registers in PEX are referred to as
R0–R15 and in PEY as S0–S15.
Context Switch
Many of the processor’s registers have secondary registers that
can be activated during interrupt servicing for a fast context
switch. The data registers in the register file, the DAG registers,
and the multiplier result register all have secondary registers.
The primary registers are active at reset, while the secondary
registers are activated by control bits in a mode control register.
Universal Registers
Universal registers can be used for general purpose tasks. The
USTAT (4) registers allow easy bit manipulations (Set, Clear,
Toggle, Test, XOR) for all system registers (control/status) of
the core.
The data bus exchange register PX permits data to be passed
between the 64-bit PM data bus and the 64-bit DM data bus, or
between the 40-bit register file and the PM data bus. These reg-
isters contain hardware to handle the data width difference.
Timer
The processors contain a core timer that can generate periodic
software interrupts. The core timer can be configured to use
FLAG3 as a timer expired signal.
Single-Cycle Fetch of an Instruction and Four Operands
The processors feature an enhanced Harvard architecture in
which the data memory (DM) bus transfers data and the pro-
gram memory (PM) bus transfers both instructions and data
(see
memory buses and on-chip instruction cache, the processor can
simultaneously fetch four operands (two over each data bus)
and one instruction (from the cache), all in a single cycle.
Instruction Cache
The processors include an on-chip instruction cache that
enables three-bus operation for fetching an instruction and four
data values. The cache is selective—only the instructions whose
fetches conflict with PM bus data accesses are cached. This
cache allows full speed execution of core, looped operations
such as digital filter multiply-accumulates, and FFT butterfly
processing.
Data Address Generators with Zero-Overhead Hardware
Circular Buffer Support
The processors’s two data address generators (DAGs) are used
for indirect addressing and implementing circular data buffers
in hardware. Circular buffers allow efficient programming of
delay lines and other data structures required in digital signal
Figure
2). With the processor’s separate program and data
Rev. C | Page 5 of 52 | September 2009
processing, and are commonly used in digital filters and Fourier
transforms. The two DAGs contain sufficient registers to allow
the creation of up to 32 circular buffers (16 primary register sets,
16 secondary). The DAGs automatically handle address pointer
wraparound, reduce overhead, increase performance, and sim-
plify implementation. Circular buffers can start and end at any
memory location.
Flexible Instruction Set
The 48-bit instruction word accommodates a variety of parallel
operations, for concise programming. For example, the proces-
sors can conditionally execute a multiply, an add, and a subtract
in both processing elements while branching and fetching up to
four 32-bit values from memory—all in a single instruction.
On-Chip Memory
The ADSP-21371 processor contains 1 megabit of internal RAM
and four megabits of internal mask-programmable ROM (see
Table 3 on Page
megabits of internal RAM and two megabits of internal mask-
programmable ROM (see
configured for different combinations of code and data storage.
Each memory block supports single-cycle, independent accesses
by the core processor and I/O processor. The processor’s mem-
ory architecture, in combination with its separate on-chip buses,
allow two data transfers from the core and one from the I/O
processor, in a single cycle.
The ADSP-21371 processor’s SRAM can be configured as a
maximum of 32k words of 32-bit data, 64k words of 16-bit data,
21.3k words of 48-bit instructions (or 40-bit data), or combina-
tions of different word sizes up to 1 megabit. All of the memory
can be accessed as 16-bit, 32-bit, 48-bit, or 64-bit words. A 16-
bit floating-point storage format is supported that effectively
doubles the amount of data that may be stored on-chip. Conver-
sion between the 32-bit floating-point and 16-bit floating-point
formats is performed in a single instruction. While each mem-
ory block can store combinations of code and data, accesses are
most efficient when one block stores data using the DM bus for
transfers, and the other block stores instructions and data using
the PM bus for transfers.
Using the DM bus and PM buses, with one bus dedicated to a
memory block, assures single-cycle execution with two data
transfers. In this case, the instruction must be available in
the cache.
On-Chip Memory Bandwidth
The internal memory architecture allows four accesses at the
same time to any of the four blocks, assuming no block con-
flicts. The total bandwidth is gained with DMD and PMD buses
(2 64-bits, core CLK) and the IOD0/1 buses (2 32-bit,
PCLK).
ROM-Based Security
The processors have a ROM security feature that provides hard-
ware support for securing user software code by preventing
unauthorized reading from the internal code when enabled.
When using this feature, the processor does not boot-load any
6) and the ADSP-21375 processor contains 0.5
ADSP-21371/ADSP-21375
Table 4 on Page
7). Each block can be