DP83849CVS/NOPB National Semiconductor, DP83849CVS/NOPB Datasheet - Page 50

• Manufacturer Part Number: DP83849CVS/NOPB
• Description: IC TXRX ETHERNET PHY DUAL 80TQFP
• Manufacturer: National Semiconductor
• Type: Transceiverr

Specifications of DP83849CVS/NOPB

• Number Of Drivers/receivers: 2/2
• Protocol: Ethernet
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 80-TQFP, 80-VQFP
• Data Rate: 100Mbps
• Supply Voltage Range: 3V To 3.6V
• Logic Case Style: TQFP
• No. Of Pins: 80
• Operating Temperature Range: 0°C To +70°C
• Msl: MSL 3 - 168 Hours
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Data Rate Max: 10Mbps
• For Use With: DP83849CVS-EVK - BOARD EVALUATION DP83849CVS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *DP83849CVS; *DP83849CVS/NOPB; DP83849CVS

www.national.com
7.1.2 Basic Mode Status Register (BMSR)
10:7
Bit
15
14
13
12
11
6
5
4
3
2
1
0
AUTO-NEGOTIATION
AUTO-NEGOTIATION
EXTENDED CAPA-
JABBER DETECT
REMOTE FAULT
MF PREAMBLE
SUPPRESSION
HALF DUPLEX
HALF DUPLEX
FULL DUPLEX
FULL DUPLEX
LINK STATUS
100BASE-T4
100BASE-TX
100BASE-TX
RESERVED
COMPLETE
10BASE-T
10BASE-T
Bit Name
ABILITY
BILITY
Table 21. Basic Mode Status Register (BMSR), address 01h
0, RO/LH
0, RO/LH
0, RO/LL
0, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
1, RO/P
Default
0, RO
0, RO
100BASE-T4 Capable:
0 = Device not able to perform 100BASE-T4 mode.
100BASE-TX Full Duplex Capable:
1 = Device able to perform 100BASE-TX in full duplex mode.
100BASE-TX Half Duplex Capable:
1 = Device able to perform 100BASE-TX in half duplex mode.
10BASE-T Full Duplex Capable:
1 = Device able to perform 10BASE-T in full duplex mode.
10BASE-T Half Duplex Capable:
1 = Device able to perform 10BASE-T in half duplex mode.
RESERVED: Write as 0, read as 0.
Preamble suppression Capable:
1 = Device able to perform management transaction with preamble
suppressed, 32-bits of preamble needed only once after reset, invalid
opcode or invalid turnaround.
0 = Normal management operation.
Auto-Negotiation Complete:
1 = Auto-Negotiation process complete.
0 = Auto-Negotiation process not complete.
Remote Fault:
1 = Remote Fault condition detected (cleared on read or by reset).
Fault criteria: Far End Fault Indication or notification from Link Part-
ner of Remote Fault.
0 = No remote fault condition detected.
Auto Negotiation Ability:
1 = Device is able to perform Auto-Negotiation.
0 = Device is not able to perform Auto-Negotiation.
Link Status:
1 = Valid link established (for either 10 or 100 Mb/s operation).
0 = Link not established.
The criteria for link validity is implementation specific. The occurrence
of a link failure condition will causes the Link Status bit to clear. Once
cleared, this bit may only be set by establishing a good link condition
and a read via the management interface.
Jabber Detect: This bit only has meaning in 10 Mb/s mode.
1 = Jabber condition detected.
0 = No Jabber.
This bit is implemented with a latching function, such that the occur-
rence of a jabber condition causes it to set until it is cleared by a read
to this register by the management interface or by a reset.
Extended Capability:
1 = Extended register capabilities.
0 = Basic register set capabilities only.
50
Description