PIC16F631-I/P Microchip Technology Inc., PIC16F631-I/P Datasheet - Page 147

• Manufacturer Part Number: PIC16F631-I/P
• Description: MCU, 8-Bit, 1KW Flash, 64 RAM, 18 I/O, PDIP-20
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F631-I/P

• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 128 Bytes
• Input Output: 18
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 20-pin PDIP
• Programmable Memory: 1.75K Bytes
• Ram Size: 64 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

11.4.7
In Single Output mode, pulse steering allows any of the
PWM pins to be the modulated signal. Additionally, the
same PWM signal can be simultaneously available on
multiple pins.
Once
(CCP1M<3:2> = 11
CCP1CON register), the user firmware can bring out
the same PWM signal to one, two, three or four output
pins by setting the appropriate STR<D:A> bits of the
PSTRCON register, as shown in Figure 11-18.
REGISTER 11-4:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
U-0
—
the
The PWM Steering mode is available only when the CCP1CON register bits CCP1M<3:2> = 11 and
P1M<1:0> = 00.
PULSE STEERING MODE
Single
Unimplemented: Read as ‘0’
STRSYNC: Steering Sync bit
1 = Output steering update occurs on next PWM period
0 = Output steering update occurs at the beginning of the instruction cycle boundary
STRD: Steering Enable bit D
1 = P1D pin has the PWM waveform with polarity control from CCP1M<1:0>
0 = P1D pin is assigned to port pin
STRC: Steering Enable bit C
1 = P1C pin has the PWM waveform with polarity control from CCP1M<1:0>
0 = P1C pin is assigned to port pin
STRB: Steering Enable bit B
1 = P1B pin has the PWM waveform with polarity control from CCP1M<1:0>
0 = P1B pin is assigned to port pin
STRA: Steering Enable bit A
1 = P1A pin has the PWM waveform with polarity control from CCP1M<1:0>
0 = P1A pin is assigned to port pin
U-0
—
and
PSTRCON: PULSE STEERING CONTROL REGISTER
Output
P1M<1:0> = 00
W = Writable bit
‘1’ = Bit is set
mode
U-0
PIC16F631/677/685/687/689/690
—
is
selected
STRSYNC
of
R/W-0
the
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
While the PWM Steering mode is active, CCP1M<1:0>
bits of the CCP1CON register select the PWM output
polarity for the P1<D:A> pins.
The PWM auto-shutdown operation also applies to
PWM Steering mode as described in Section 11.4.4
“Enhanced
auto-shutdown event will only affect pins that have
PWM outputs enabled.
STRD
Note:
The associated TRIS bits must be set to
output (‘0’) to enable the pin output driver
in order to see the PWM signal on the pin.
PWM
R/W-0
STRC
(1)
Auto-shutdown
x = Bit is unknown
R/W-0
STRB
DS41262D-page 145
mode”.
R/W-1
STRA
bit 0
An