PIC16F72-I/SP Microchip Technology Inc., PIC16F72-I/SP Datasheet - Page 92
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC16F72-I/SP
Manufacturer Part Number
PIC16F72-I/SP
Description
28 PIN, 3.5 KB FLASH, 128 RAM, 22 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F72-ISP.pdf
(136 pages)
Specifications of PIC16F72-I/SP
A/d Inputs
5-Channel, 8-Bit
Cpu Speed
5 MIPS
Eeprom Memory
0 Bytes
Input Output
22
Interface
I2C/SPI
Memory Type
Flash
Number Of Bits
8
Package Type
28-pin SPDIP
Programmable Memory
3.5K Bytes
Ram Size
128 Bytes
Speed
20 MHz
Timers
2-8-bit, 1-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F72-I/SP
Manufacturer:
ST
Quantity:
30
Company:
Part Number:
PIC16F72-I/SP
Manufacturer:
MIC40
Quantity:
55
Part Number:
PIC16F72-I/SP
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
PIC16F72-I/SPC01
Manufacturer:
MIC
Quantity:
6 264
PIC16F72
14.1
DS39597B-page 90
PIC16LF72
PIC16F72
D010
D010A
D010
D013
D015*
D020
D021
D020
D021
D023*
Note 1: This is the limit to which V
Param
(Industrial)
(Industrial, Extended)
No.
*
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
4: For RC osc configuration, current through R
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
7: When BOR is enabled, the device will operate correctly until the V
DC Characteristics: PIC16F72 (Industrial, Extended)
I
∆I
I
∆I
DD
PD
Sym
These parameters are characterized but not tested.
and are not tested.
loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an
impact on the current consumption. The test conditions for all I
are:
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
estimated by the formula Ir = V
characterization and is for design guidance only. This is not tested.
added to the base I
BOR
BOR
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
MCLR = V
Supply Current (Notes 2, 5)
Brown-out Reset Current
(Note 6)
Power-down Current (Notes 3, 5)
Brown-out Reset Current
(Note 6)
DD
Characteristic
; WDT enabled/disabled as specified.
DD
or I
PIC16LF72
PIC16LF72
PIC16F72
PIC16F72
PIC16LF72 (Industrial) (Continued)
PD
DD
measurement.
can be lowered without losing RAM data.
DD
/2R
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
Min
EXT
—
—
—
—
—
—
—
—
-
(mA) with R
Typ† Max Units
EXT
0.4
0.9
5.2
2.0
0.1
5.0
0.1
25
25
25
is not included. The current through the resistor can be
200
200
2.0
48
15
30
42
19
4
5
EXT
in kΩ.
mA
mA
mA
µA
µA
µA
µA
µA
µA
µA
-40°C ≤ T
DD
XT, RC osc configuration
F
LP osc configuration
F
XT, RC osc configuration
F
HS osc configuration
F
BOR enabled, V
V
V
V
V
BOR enabled, V
OSC
OSC
OSC
OSC
DD
DD
DD
DD
measurements in active Operation mode
BOR
= 3.0V, WDT enabled, -40°C to +85°C
= 3.0V, WDT disabled, -40°C to +85°C
= 4.0V, WDT enabled, -40°C to +85°C
= 4.0V, WDT disabled, -40°C to +85°C
A
A
A
= 4 MHz, V
= 32 kHz, V
= 4 MHz, V
= 20 MHz, V
voltage trip point is reached.
≤ +85°C for industrial
≤ +85°C for industrial
≤ +125°C for extended
2002 Microchip Technology Inc.
Conditions
DD
DD
DD
DD
DD
DD
DD
= 5.0V
= 5.0V
= 3.0V (Note 4)
= 5.5V (Note 4)
= 3.0V, WDT disabled
= 5.5V
DD
and V
SS
.