ATmega162 Atmel Corporation, ATmega162 Datasheet - Page 149

• Manufacturer Part Number: ATmega162
• Manufacturer: Atmel Corporation

Specifications of ATmega162

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 35
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 6
• Input Capture Channels: 2
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8-bit
Timer/Counter
Register
Description
Timer/Counter Control
Register – TCCR2
2513K–AVR–07/09
• Bit 7 – FOC2: Force Output Compare
The FOC2 bit is only active when the WGM bits specify a non-PWM mode. However, for ensur-
ing compatibility with future devices, this bit must be set to zero when TCCR2 is written when
operating in PWM mode. When writing a logical one to the FOC2 bit, an immediate Compare
Match is forced on the Waveform Generation unit. The OC2 output is changed according to its
COM21:0 bits setting. Note that the FOC2 bit is implemented as a strobe. Therefore it is the
value present in the COM21:0 bits that determines the effect of the forced compare.
A FOC2 strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR2 as TOP.
The FOC2 bit is always read as zero.
• Bit 6, 3 – WGM21:0: Waveform Generation Mode
These bits control the counting sequence of the counter, the source for the maximum (TOP)
counter value, and what type of waveform generation to be used. Modes of operation supported
by the Timer/Counter unit are: Normal mode, Clear Timer on Compare match (CTC) mode, and
two types of Pulse Width Modulation (PWM) modes. See
page
Table 60. Waveform Generation Mode Bit Description
Note:
Bit
Read/Write
Initial Value
Mode
0
1
2
3
143.
1. The CTC2 and PWM2 bit definition names are now obsolete. Use the WGM21:0 definitions.
WGM21
(CTC2)
However, the functionality and location of these bits are compatible with previous versions of
the timer.
0
0
1
1
FOC2
W
7
0
WGM20
(PWM2)
WGM20
0
1
0
1
R/W
6
0
Timer/Counter Mode
of Operation
Normal
PWM, Phase Correct
CTC
Fast PWM
COM21
R/W
5
0
COM20
R/W
4
0
WGM21
R/W
3
0
(1)
TOP
0xFF
0xFF
OCR2
0xFF
CS22
R/W
2
0
Table 60
Update of
OCR2 at
Immediate
TOP
Immediate
TOP
CS21
R/W
1
0
and
ATmega162/V
“Modes of Operation” on
CS20
R/W
0
0
TOV2 Flag
Set on
MAX
BOTTOM
MAX
MAX
TCCR2
149