ATxmega64A3 Atmel Corporation, ATxmega64A3 Datasheet - Page 73

• Manufacturer Part Number: ATxmega64A3
• Manufacturer: Atmel Corporation

Specifications of ATxmega64A3

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 50
• Ext Interrupts: 50
• Usb Speed: No
• Usb Interface: No
• Spi: 10
• Twi (i2c): 2
• Uart: 7
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 7
• Output Compare Channels: 22
• Input Capture Channels: 22
• Pwm Channels: 22
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.8.2
8077H–AVR–12/09
CHnCTRL – Event Channel n Control Register
.
• Bit 7 - Reserved
This bit is reserved and will always be read as zero. For compatibility with future devices, always
write this bit to zero when this register is written.
• Bit 6:5 - QDIRM[1:0]: Quadrature Decode Index Recognition Mode
These bits determine the quadrature state for the QDPH0 and QDPH90 signals where a valid
index signal is recognized and the counter index data event is given according to
page
nal is used.
These bits are only available for CH0CTRL, CH2CTRL and CH4CTRL
Table 6-5.
• Bit 4 - QDIEN: Quadrature Decode Index Enable
When this bit is set the event channel will be used as QDEC index source, and the index data
event will be enabled.
These bit is only available for CH0CTRL, CH2CTRL and CH4CTRL.
• Bit 3 - QDEN: Quadrature Decode Enable
Setting this bit enables QDEC operation.
These bits is only available for CH0CTRL, CH2CTRL and CH4CTRL.
• Bit 2:0 - DIGFILT[2:0]: Digital Filter Coefficient
These bits define the length of digital filtering used. Events will be passed through to the event
channel only when the event source has been active and sampled with the same level for a a
number of peripheral clock for the number of cycles as defined by DIGFILT.
Bit
Read/Write
Initial Value
QDIRM[1:0]
0
0
1
1
73. These bits is only needed to set when a quadrature encoed with a connected index sig-
0
1
0
1
QDIRM Bit Settings
7
R
0
-
Index Recognition State
{QDPH0, QDPH90} = 0b00
{QDPH0, QDPH90} = 0b01
{QDPH0, QDPH90} = 0b10
{QDPH0, QDPH90} = 0b11
R/W
6
0
QDIRM[1:0]
R/W
5
0
QDIEN
R/W
4
0
QDEN
R/W
3
0
R/W
2
0
DIGFILT[2:0]
R/W
1
0
XMEGA A
R
0
0
Table 6-5 on
CHnCTRL
73