SAM3S16C Atmel Corporation, SAM3S16C Datasheet - Page 554

• Manufacturer Part Number: SAM3S16C
• Manufacturer: Atmel Corporation

Specifications of SAM3S16C

• Flash (kbytes): 1024 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 100 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 39
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 31-8. Transmitter Block Diagram
31.7.3
512
512
SSC_TCMR.STTDLY != 0
SAM3S16
SAM3S16
Receiver Operations
SSC_RCMR.START
SSC_TFMR.DATLEN
SSC_TFMR.FSDEN
RXEN
TX Start
RF
RC0R
Selector
Start
A received frame is triggered by a start event and can be followed by synchronization data
before data transmission.
The start event is configured setting the Receive Clock Mode Register (SSC_RCMR).
“Start” on page 513.
The frame synchronization is configured setting the Receive Frame Mode Register
(SSC_RFMR).
The receiver uses a shift register clocked by the receiver clock signal and the start mode
selected in the SSC_RCMR. The data is transferred from the shift register depending on the
data format selected.
When the receiver shift register is full, the SSC transfers this data in the holding register, the sta-
tus flag RXRDY is set in SSC_SR and the data can be read in the receiver holding register. If
another transfer occurs before read of the RHR register, the status flag OVERUN is set in
SSC_SR and the receiver shift register is transferred in the RHR register.
TXEN
RX Start
RF
SSC_TCMR.START
SSC_THR
Selector
Transmit Shift Register
Start
See “Frame Sync” on page 515.
0
TX Start
SSC_TCMR.STTDLY
SSC_TFMR.FSDEN
SSC_TFMR.DATNB
SSC_TFMR.DATDEF
SSC_TFMR.MSBF
1
SSC_TSHR
TX Controller counter reached STTDLY
SSC_TFMR.FSLEN
SSC_CRTXEN
SSC_CRTXDIS
TX Controller
SSC_SRTXEN
Transmitter Clock
TXEN
11117B–ATARM–18-Oct-11
11117B–ATARM–18-Oct-11
TD
See