MC56F8366 Freescale Semiconductor, Inc, MC56F8366 Datasheet - Page 119
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
MC56F8366
Manufacturer Part Number
MC56F8366
Description
56f8300 16-bit Digital Signal Controllers
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC56F8366.pdf
(184 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC56F8366MFV60
Manufacturer:
Power-one
Quantity:
268
Company:
Part Number:
MC56F8366MFVE
Manufacturer:
Freescale
Quantity:
440
Company:
Part Number:
MC56F8366MFVE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC56F8366MFVE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC56F8366VFV60
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
MC56F8366VFVE
Manufacturer:
Freescale
Quantity:
43
Company:
Part Number:
MC56F8366VFVE
Manufacturer:
MOTOLOLA
Quantity:
439
Company:
Part Number:
MC56F8366VFVE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC56F8366VFVE
Manufacturer:
FREESCALE
Quantity:
20 000
6.5.1.2
This bit reflects the current (non-clocked) state of the EMI_MODE pin. During reset, this bit, coupled with
the EXTBOOT signal, is used to initialize address bits [19:16] either as GPIO or as address. These settings
can be explicitly overwritten using the appropriate GPIO peripheral enable register at any time after reset.
In addition, this pin can be used as a general purpose input pin after reset.
6.5.1.3
6.5.1.4
This bit is always read as 0. Writing a 1 to this bit will cause the part to reset.
6.5.1.5
6.5.1.6
6.5.2
Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A
reset (other than POR) will only set bits in the register; bits are not cleared. Only software should clear this
register.
Freescale Semiconductor
Preliminary
•
•
•
•
•
•
•
•
•
•
•
•
Base + $1
RESET
0 = External address bits [19:16] are initially programmed as GPIO
1 = When booted with EXTBOOT = 1, A[19:16] are initially programmed as address. If EXTBOOT is 0,
they are initialized as GPIO.
0 = OnCE clock to 56800E core enabled when core TAP is enabled
1 = OnCE clock to 56800E core is always enabled
00 - Stop mode will be entered when the 56800E core executes a STOP instruction
01 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be
reprogrammed in the future
10 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be
changed by resetting the device
11 - Same operation as 10
00 - Wait mode will be entered when the 56800E core executes a WAIT instruction
01 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be
reprogrammed in the future
10 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only be
changed by resetting the device
11 - Same operation as 10
Read
Write
SIM Reset Status Register (SIM_RSTSTS)
EMI_MODE (EMI_MODE)—Bit 6
OnCE Enable (OnCE EBL)—Bit 5
Software Reset (SW RST)—Bit 4
Stop Disable (STOP_DISABLE)—Bits 3–2
Wait Disable (WAIT_DISABLE)—Bits 1–0
15
0
0
Figure 6-4 SIM Reset Status Register (SIM_RSTSTS)
14
0
0
13
0
0
12
0
0
56F8366 Technical Data, Rev. 6
11
0
0
10
0
0
9
0
0
8
0
0
7
0
0
6
0
0
SWR
5
COPR
4
EXTR
3
POR
Register Descriptions
2
1
0
0
0
0
0
119