MBM29SL160TD Fujitsu Microelectronics, Inc., MBM29SL160TD Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
MBM29SL160TD
Manufacturer Part Number
MBM29SL160TD
Description
Flash Memory 16m 2m X 8/1m X 16 Bit
Manufacturer
Fujitsu Microelectronics, Inc.
Datasheet
1.MBM29SL160TD.pdf
(61 pages)
DQ
Exceeded Timing Limits
DQ
Sector Erase Timer
DQ
Toggle Bit II
DQ
these conditions DQ
cycle was not successfully completed. Data Polling is the only operating function of the devices under this
condition. The CE circuit will partially power down the device under these conditions (to approximately 2 mA).
The OE and WE pins will control the output disable functions as described in Tables 4 and 5.
The DQ
case the devices lock out and never complete the Embedded Algorithm operation. Hence, the system never
reads a valid data on DQ
DQ
used. If this occurs, reset the device with command sequence.
After the completion of the initial sector erase command sequence the sector erase time-out will begin. DQ
remain low until the time-out is complete. Data Polling and Toggle Bit are valid after the initial sector erase
command sequence.
If Data Polling or the Toggle Bit I indicates the device has been written with a valid erase command, DQ
be used to determine if the sector erase timer window is still open. If DQ
erase cycle has begun; attempts to write subsequent commands to the device will be ignored until the erase
operation is completed as indicated by Data Polling or Toggle Bit I. If DQ
additional sector erase commands. To insure the command has been accepted, the system software should
check the status of DQ
the second status check, the command may not have been accepted.
See Table 8: Hardware Sequence Flags.
This toggle bit II, along with DQ
Algorithm or in Erase Suspend.
Successive reads from the erasing sector will cause DQ
devices are in the erase-suspended-read mode, successive reads from the erase-suspended sector will cause
DQ
address of the non-erase suspended sector will indicate a logic “1” at the DQ
DQ
Program operation is in progress. The behavior of these two status bits, along with that of DQ
as follows:
For example, DQ
(DQ
Furthermore, DQ
mode, DQ
5
3
2
5
5
2
6
2
bit will indicate a “1.” Please note that this is not a device failure condition since the devices were incorrectly
will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under
to toggle. When the devices are in the erase-suspended-program mode, successive reads from the byte
is different from DQ
toggles while DQ
5
failure condition may also appear if a user tries to program a non blank location without erasing. In this
2
toggles if this bit is read from an erasing sector.
2
2
and DQ
can also be used to determine which sector is being erased. When the device is in the erase
5
will produce a “1”. This is a failure condition which indicates that the program or erase
6
3
does not.) See also Table 9 and Figure 18.
prior to and following each subsequent Sector Erase command. If DQ
2
7
MBM29SL160TD
in that DQ
bit and DQ
6
can be used together to determine if the erase-suspend-read mode is in progress.
6
, can be used to determine whether the devices are in the Embedded Erase
6
6
toggles only when the standard program or Erase, or Erase Suspend
never stops toggling. Once the devices have exceeded timing limits, the
2
to toggle during the Embedded Erase Algorithm. If the
-10/-12
/MBM29SL160BD
3
3
is high (“1”) the internally controlled
is low (“0”), the device will accept
2
bit.
7
, is summarized
3
were high on
-10/-12
3
may
3
will
25