FDC37C665IR SMSC Corporation, FDC37C665IR Datasheet - Page 108
![no-image](/images/no-image-200.jpg)
FDC37C665IR
Manufacturer Part Number
FDC37C665IR
Description
3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
Manufacturer
SMSC Corporation
Datasheet
1.FDC37C665IR.pdf
(162 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FDC37C665IR
Manufacturer:
SMC
Quantity:
108
Part Number:
FDC37C665IR
Manufacturer:
SMC
Quantity:
20 000
- Current page: 108 of 162
- Download datasheet (563Kb)
are
mode using program control of the control
signals.
Interrupts
The interrupts are enabled by serviceIntr in the
ecr register.
serviceIntr = 1 Disables the DMA and all of the
serviceIntr = 0Enables the selected interrupt
The interrupt generated is ISA friendly in that it
must pulse the interrupt line low, allowing for
interrupt sharing.
following the interrupt event, the interrupt line is
tri-stated so that other interrupts may assert.
An interrupt is generated when:
1.For DMA transfers: When serviceIntr is 0,
2.For Programmed I/O:
dmaEn is 1 and the DMA TC is received.
a.
always possible with standard or PS/2
direction
writeIntrThreshold or more free bytes in
the FIFO.
generated when serviceIntr is cleared
to
writeIntrThreshold or more free bytes in
the FIFO.
When serviceIntr is 0, dmaEn is 0,
0
service interrupts.
condition.
condition is valid, then the
interrupt
immediately when this bit is
changed from a 1 to a 0. This
can occur during Programmed
I/O if the number of bytes
removed or added from/to the
FIFO does not cross the
threshold.
is
whenever
After a brief pulse low
Also, an interrupt is
0
and
If the interrupting
is
there
there
generated
are
are
108
3. When nErrIntrEn is 0 and nFault transitions
4. When ackIntEn is 1 and the nAck signal
FIFO Operation
The
configuration registers. All data transfers to or
from the parallel port can proceed in DMA or
Programmed I/O (non-DMA) mode as indicated
by the selected mode.
selecting the Parallel Port FIFO mode or ECP
Parallel Port Mode. (FIFO test mode will be
addressed separately.) After a reset, the FIFO
is disabled. Each data byte is transferred by a
Programmed I/O cycle or PDRQ depending on
the selection of DMA or Programmed I/O mode.
The following paragraphs detail the operation of
the FIFO flow control.
<threshold> ranges from 1 to 16.
parameter FIFOTHR, which the user programs,
is one less and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer
periods of time between service requests, but
requires faster servicing of the request for both
read and write cases. The host must be very
responsive to the service request. This is the
desired case for use with a "fast" system.
b.
from high to low or when nErrIntrEn is set
from 1 to 0 and nFault is asserted.
transitions from a low to a high.
FIFO
(1)When serviceIntr is 0, dmaEn is 0,
threshold
direction is 1 and there are
readIntrThreshold
bytes in the FIFO.
interrupt is generated when
serviceIntr is cleared to 0
whenever
readIntrThreshold
bytes in the FIFO.
is
The FIFO is used by
In these descriptions,
set
there
in
or
or
the
Also, an
more
more
chip
The
are
Related parts for FDC37C665IR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN83C183-JD](/images/no-image3.png)
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N769TQFP](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47M102S-MC](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N267-MN](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![USB20H04-JD](/images/no-image3.png)
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37M602](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37B777](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37C672](/images/no-image3.png)
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
![COM90C66LJP](/images/no-image3.png)
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869TQFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![USB97C100QFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N227-MN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: