lan9311 Standard Microsystems Corp., lan9311 Datasheet - Page 95
lan9311
Manufacturer Part Number
lan9311
Description
Lan9311/lan9311i Two Port 10/100 Managed Ethernet Switch With 16-bit Non-pci Cpu Interface
Manufacturer
Standard Microsystems Corp.
Datasheet
1.LAN9311.pdf
(460 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lan9311-NU
Manufacturer:
CINCERA
Quantity:
3 023
Company:
Part Number:
lan9311-NU
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
lan9311-NU
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
lan9311-NZW
Manufacturer:
Standard
Quantity:
2
Company:
Part Number:
lan9311-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
lan9311I-NZW
Manufacturer:
Standard
Quantity:
836
Company:
Part Number:
lan9311I-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 95 of 460
- Download datasheet (5Mb)
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
SMSC LAN9311/LAN9311i
7.2.9.1
7.2.9.2
7.2.10
7.2.10.1
Note: The power-down modes of each PHY (Port 1 PHY and Port 2 PHY) are controlled
Note: The PHY power-down modes do not reload or reset the PHY registers.
PHY General Power-Down
This power-down mode is controlled by bit 11 of the
(PHY_BASIC_CONTROL_x). In this mode the entire PHY, except the PHY management control
interface, is powered down. The PHY will remain in this power-down state as long as bit 11 is set.
When bit 11 is cleared, the PHY powers up and is automatically reset.
PHY Energy Detect Power-Down
This power-down mode is enabled by setting bit 13 (EDPWRDOWN) of the
Control/Status Register
detected on the line, the entire PHY is powered down except for the PHY management control
interface, the SQUELCH circuit, and the ENERGYON logic. The ENERGYON logic is used to detect
the presence of valid energy from 100BASE-TX, 10BASE-T, or auto-negotiation signals and is
responsible for driving the ENERGYON signal (bit 1) of the
(PHY_MODE_CONTROL_STATUS_x).
In this mode, when the ENERGYON signal is cleared, the PHY is powered down and no data is
transmitted from the PHY. When energy is received, via link pulses or packets, the ENERGYON signal
goes high, and the PHY powers up. The PHY automatically resets itself into its previous state prior to
power-down, and asserts the INT7 interrupt (bit 7) of the
(PHY_INTERRUPT_SOURCE_x). The first and possibly second packet to activate ENERGYON may
be lost.
W h e n b i t 1 3 ( E D P W R D O W N ) o f t h e
(PHY_MODE_CONTROL_STATUS_x)
The energy detect power down feature is part of the broader power management features of the
LAN9311/LAN9311i and can be used to trigger the power management event output pin (PME). This
is accomplished by enabling the energy detect power-down feature of the PHY as described above,
and setting the corresponding energy detect enable (bit 14 for Port 1 PHY, bit 15 for Port 2 PHY) of
the
on page 46
PHY Resets
In addition to the chip-level hardware reset (nRST) and Power-On Reset (POR), the PHY supports
three block specific resets. These are discussed in the following sections. For detailed information on
all LAN9311/LAN9311i resets and the reset sequence refer to
Note: The DIGITAL_RST bit in the
PHY Software Reset via RESET_CTL
The PHY can be reset via the
setting bit 1 (PHY1_RST), and the Port 2 PHY is reset by setting bit 2 (PHY2_RST). These bits are
self clearing after approximately 102uS. This reset does not reload the configuration strap values into
the PHY registers.
Power Management Control Register
independently.
Only a hardware reset (nRST) or an EEPROM RELOAD command will automatically reload
the configuration strap values into the PHY registers. For all other PHY resets, these values
will need to be manually configured via software.
for additional information.
(PHY_MODE_CONTROL_STATUS_x). When in this mode, if no energy is
Reset Control Register
DATASHEET
Reset Control Register (RESET_CTL)
is low, energy detect power-down is disabled.
(PMT_CTRL). Refer to
95
P o r t x P H Y M o d e C o n t r o l / St a t u s R e g i s t e r
(RESET_CTL). The Port 1 PHY is reset by
Port x PHY Interrupt Source Flags Register
Port x PHY Mode Control/Status Register
Port x PHY Basic Control Register
Section 4.2, "Resets," on page
Section 4.3, "Power Management,"
does not reset the PHYs.
Revision 1.2 (04-08-08)
Port x PHY Mode
36.
Related parts for lan9311
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: