xr17v254 Exar Corporation, xr17v254 Datasheet - Page 5

• Manufacturer Part Number: xr17v254
• Description: 66mhz Pci Bus Quad Uart With Power Management Support
• Manufacturer: Exar Corporation

REV. 1.0.0
PIN DESCRIPTIONS
ANCILLARY SIGNALS
TMRCK
MPIO0
MPIO1
MPIO2
MPIO3
MPIO4
MPIO5
MPIO6
MPIO7
XTAL1
XTAL2
EEDO
EECK
EECS
N
EEDI
ENIR
RI3#
VCC
AME
19, 34, 45, 137
64, 90,112, 4,
P
108
107
109
116
115
114
113
110
59
74
73
68
67
66
65
69
70
IN
#
T
66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
YPE
O
O
O
O
I
I
I
I
I
UART channel 3 Ring Indicator or general purpose input (active LOW).
Multi-purpose input/output 0. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT
Multi-purpose input/output 1. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT.
Multi-purpose input/output 2. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT.
Multi-purpose input/output 3. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT.
Multi-purpose input/output 4. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT.
Multi-purpose input/output 5. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT.
Multi-purpose input/output 6. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT.
Multi-purpose input/output 7. The function of this pin is defined thru the Con-
figuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and MPIOINT.
Serial clock to EEPROM. An internal clock of CLK divide by 256 is used for
reading the vendor and sub-vendor ID during power up or reset. However, it
can be manually clocked thru the Configuration Register REGB.
Chip select to a EEPROM device like 93C46. It is manually selectable thru
the Configuration Register REGB. Requires a pull-up 4.7K ohm resistor for
external sensing of EEPROM during power up. See DAN112 for further
details.
Write data to EEPROM device. It is manually accessible thru the Configura-
tion Register REGB.
Read data from EEPROM device. It is manually accessible thru the Configu-
ration Register REGB.
Crystal or external clock input.
Crystal or buffered clock output.
16-bit timer/counter external clock input.
Infrared mode enable (active high). This pin is sampled during power up, fol-
lowing a hardware reset (RST#) or soft-reset (register RESET). It can be
used to start up all 4 UARTs in the infrared mode. The sampled logic state is
transferred to MCR bit [6] in the UART.
Power supply for the UART core logic and PCI bus I/O - 3.3V only. The V254
is PCI 3.0 signalling compliant at 3.3V operation. The non-PCI inputs (except
XTAL1) are 5V tolerant. This includes all the serial (modem) inputs.
5
D
ESCRIPTION
XR17V254