vsc055xkm-01 Maxim Integrated Products, Inc., vsc055xkm-01 Datasheet - Page 104
vsc055xkm-01
Manufacturer Part Number
vsc055xkm-01
Description
Enhanced I?c Backplane Controller
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.VSC055XKM-01.pdf
(133 pages)
- Current page: 104 of 133
- Download datasheet (2Mb)
Operating Notes for the Master Serial Interface
Revision 4.1
January 2008
Encoded Two-Wire Serial Commands
52h - Read byte with stop, no acknowledge (used at the end of read telegrams)
54h - Read byte with acknowledge (used for middle bytes during sequential reads)
58h - Write byte (used for end of address writes or middle bytes of sequential writes)
59h - Write byte with start (used for the beginning of all telegrams and restarts)
5Ah - Write byte with stop (used for end of write telegrams)
60h - Soft reset
The sequence for normal two-wire serial protocol compliant write operations is:
1.
2.
3.
Bit
1
0
Issue start bit, send the slave device address and write bit (0) in the LSB.
Send the slave device's register address, this can zero bytes or in some slave devices this may be multiple
Send the byte to be written to the slave device, followed by a stop bit.
bytes.
Pseudo-code to perform two-wire serial protocol compliant writes
using this core:
Send slave device address:
1) <{slave_address[6:0],1'b0}>
2)
3)
4)
did not respond
Send register address:
5)
6)
7)
8)
did not acknowledge
Bit Label
STO
STA
Write 59h to the MIC register (command)
Poll the MIS register (status) until bit 0 = 1
Test bit 1, if set continue, if clear then the slave device
<slave's register address>
Write 58h to MIC register (command)
Poll the MIS register (status) until bit 0 = 1
Test bit 1, if set continue, if clear then the slave device
Access
R/W
R/W
Description
Stop Condition
This bit controls the STOP condition of a serial transfer.
Setting this bit directs the master serial interface to generate a stop bit
sequence (rising edge on SDA while SCL is HIGH) after transferring the
immediate byte. This should only be done to end a telegram.
After a reset or power on, this bit is cleared.
Start Condition
This bit provides control for the start condition of a serial transfer.
Setting this bit directs the master serial interface to generate a start bit
sequence (falling edge on SDA while SCL is HIGH) prior to transferring the
immediate byte. This operation should be initiated at the beginning of a
telegram and as required for restarts during read transactions.
After a reset or power on, this bit is cleared.
104 of 133
-->
-->
MID register (data)
MID register (data)
VSC055-01
Data Sheet
Related parts for vsc055xkm-01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Nonvolatile Ram Controller Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.3v Single-piece 8mb Nonvolatile Sram Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Pon Triplexer Control And Monitoring Circuit Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ttl Compatible Cmos Analog Switches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Improved Low-power, Cmos Analog Switches With Latches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Windows Vista-compliant, Stereo Class Ab Speaker Amplifiers And Directdrive Headphone Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
4a, 20ns, Dual Mosfet Drivers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Nicd/nimh Battery Fast-charge Controllers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.6v, 1w Autoramping Power Amplifier For 900mhz Applications Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
2.7v, Single-supply, Cellular-band Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
5ghz Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Evaluation Kits for the MAX3514
Manufacturer:
Maxim Integrated Products, Inc.
Part Number:
Description:
5v, Differential Input, Directdrive, 130mw Stereo Headphone Amplifiers With Shutdown Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Accurate I2c Rtc With Integrated Tcxo/crystal/fram
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ds1863 Burst-mode Pon Controller With Integrated Monitoring
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet: