vsc055xkm-01 Maxim Integrated Products, Inc., vsc055xkm-01 Datasheet - Page 14
vsc055xkm-01
Manufacturer Part Number
vsc055xkm-01
Description
Enhanced I?c Backplane Controller
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.VSC055XKM-01.pdf
(133 pages)
- Current page: 14 of 133
- Download datasheet (2Mb)
Table 1. CKSEL Settings (continued)
2.5
Revision 4.1
January 2008
The VSC055-01 device can operate at frequencies other than those listed in the above table and maintain
accurate fan speed and LED control frequencies, as well as continue to meet both the Standard mode
(100 kHz) and Fast mode (400 kHz) serial interface timings. Frequencies from 8.0 MHz to 12.5 MHz and
32.0 MHz to 75.0 MHz are allowable as long as they meet the AC timing requirements. For information on
AC timing requirements, see
The Clock Divider Control Register (CDC), located at FEh, can be programmed to override the divider
value selected by the CKSEL input pins and adjust the divided clock source used for the fan speed and
LED control logic. The pulse-width modulated outputs are not controlled by this logic and can vary based
on the input frequency. For examples of various frequency settings, based on both the CKSEL inputs and
the appropriate CDC register value,
Logic within the VSC055-01 synchronizes the divided clocks between devices attached to the same two-
wire serial bus with no more than 200 ns of skew when the fixed divider frequencies are used. Multiple
devices can then be used to drive different LEDs at the same frequency, providing a synchronized visible
indication. Devices attached to different two-wire serial busses can be synchronized by enabling the
SYNC# pin. This pin, which is connected to the SYNC# pin of all VSC055-01 devices in the system,
provides a sync pulse based on a programmable delay that is greater than the slowest selected LED flash
rate. For more information about the programmable capabilities of this feature, see
Control (CSC),”
Power-on Reset
Power-on reset (POR) is accomplished by the use of an internal POR cell. After power on, the serial
interface state machine always returns an idle state while waiting for a START condition to appear on the
SCL and SDA pins. A proper power-on reset sequence clears the serial interface state machine, the clock
generators, the control registers, the I/O control logic, and the port bypass control logic. The divided clocks
used for LED flash rate generation are also in a known state. Regardless of the effectiveness of the power-
on reset mechanism, it is strongly recommended that the control registers and the I/O control logic be
cleared through the Soft Reset register bit. This can be accomplished by writing a 80h to the BCT Register
(FCh), followed immediately by a STOP condition. This bit is self-resetting and does not require further
attention.
CKSEL2
VDD
VDD
VDD
page 111.
CKSEL1
VSS
VDD
VDD
“AC Characteristics,”
see“FEh: Clock Divider Control (CDC),”
CKSEL0
VDD
VDD
VSS
14 of 133
page 119.
Input Clock
53.125 MHz
33.33 MHz
50.0 MHz
Divider
÷4
÷6
÷6
page 113.
“FDh: Clock Select
Internal Clock
8.854 MHz
8.33 MHz
8.33 MHz
VSC055-01
Data Sheet
Related parts for vsc055xkm-01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Nonvolatile Ram Controller Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.3v Single-piece 8mb Nonvolatile Sram Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Pon Triplexer Control And Monitoring Circuit Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ttl Compatible Cmos Analog Switches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Improved Low-power, Cmos Analog Switches With Latches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Windows Vista-compliant, Stereo Class Ab Speaker Amplifiers And Directdrive Headphone Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
4a, 20ns, Dual Mosfet Drivers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Nicd/nimh Battery Fast-charge Controllers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.6v, 1w Autoramping Power Amplifier For 900mhz Applications Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
2.7v, Single-supply, Cellular-band Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
5ghz Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Evaluation Kits for the MAX3514
Manufacturer:
Maxim Integrated Products, Inc.
Part Number:
Description:
5v, Differential Input, Directdrive, 130mw Stereo Headphone Amplifiers With Shutdown Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Accurate I2c Rtc With Integrated Tcxo/crystal/fram
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ds1863 Burst-mode Pon Controller With Integrated Monitoring
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet: