PIC18F23K20-E/MLQTP MICROCHIP [Microchip Technology], PIC18F23K20-E/MLQTP Datasheet - Page 295

• Manufacturer Part Number: PIC18F23K20-E/MLQTP
• Description: 28/40/44-Pin Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
• Manufacturer: MICROCHIP [Microchip Technology]

REGISTER 23-4:
REGISTER 23-5:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value when device is unprogrammed
bit 7
bit 6-4
bit 3
bit 2
bit 1
bit 0
bit 7
Legend:
R = Readable bit
-n = Value when device is unprogrammed
bit 7
bit 6
bit 5-3
bit 2
bit 1
bit 0
MCLRE
DEBUG
R/P-1
R/P-1
MCLRE: MCLR Pin Enable bit
1 = MCLR pin enabled; RE3 input pin disabled
0 = RE3 input pin enabled; MCLR disabled
Unimplemented: Read as ‘0’
HFOFST: HFINTOSC Fast Start-up
1 = HFINTOSC starts clocking the CPU without waiting for the oscillator to stabilize.
0 = The system clock is held off until the HFINTOSC is stable.
LPT1OSC: Low-Power Timer1 Oscillator Enable bit
1 = Timer1 configured for low-power operation
0 = Timer1 configured for higher power operation
PBADEN: PORTB A/D Enable bit
(Affects ADCON1 Reset state. ADCON1 controls PORTB<4:0> pin configuration.)
1 = PORTB<4:0> pins are configured as analog input channels on Reset
0 = PORTB<4:0> pins are configured as digital I/O on Reset
CCP2MX: CCP2 MUX bit
1 = CCP2 input/output is multiplexed with RC1
0 = CCP2 input/output is multiplexed with RB3
DEBUG: Background Debugger Enable bit
1 = Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins
0 = Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug
XINST: Extended Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
Unimplemented: Read as ‘0’
LVP: Single-Supply ICSP Enable bit
1 = Single-Supply ICSP enabled
0 = Single-Supply ICSP disabled
Unimplemented: Read as ‘0’
STVREN: Stack Full/Underflow Reset Enable bit
1 = Stack full/underflow will cause Reset
0 = Stack full/underflow will not cause Reset
XINST
R/P-0
U-0
—
CONFIG3H: CONFIGURATION REGISTER 3 HIGH
CONFIG4L: CONFIGURATION REGISTER 4 LOW
P = Programmable bit
P = Programmable bit
U-0
U-0
—
—
Advance Information
U-0
U-0
—
—
U = Unimplemented bit, read as ‘0’
x = Bit is unknown
U = Unimplemented bit, read as ‘0’
x = Bit is unknown
HFOFST
R/P-1
PIC18F2XK20/4XK20
U-0
—
LPT1OSC
R/P-0
R/P-1
LVP
PBADEN
R/P-1
U-0
—
DS41303B-page 293
CCP2MX
STVREN
R/P-1
R/P-1
bit 0
bit 0