AT90USB1286-16MU ATMEL [ATMEL Corporation], AT90USB1286-16MU Datasheet - Page 58
AT90USB1286-16MU
Manufacturer Part Number
AT90USB1286-16MU
Description
Microcontroller with 64/128K Bytes of ISP Flash and USB Controller
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT90USB1286-16MU.pdf
(434 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 58 of 434
- Download datasheet (4Mb)
8. System Control and Reset
8.0.1
8.0.2
58
AT90USB64/128
Resetting the AVR
Reset Sources
During reset, all I/O Registers are set to their initial values, and the program starts execution
from the Reset Vector. The instruction placed at the Reset Vector must be a JMP – Absolute
Jump – instruction to the reset handling routine. If the program never enables an interrupt
source, the Interrupt Vectors are not used, and regular program code can be placed at these
locations. This is also the case if the Reset Vector is in the Application section while the Interrupt
Vectors are in the Boot section or vice versa. The circuit diagram in
logic.
The I/O ports of the AVR are immediately reset to their initial state when a reset source goes
active. This does not require any clock source to be running.
After all reset sources have gone inactive, a delay counter is invoked, stretching the internal
reset. This allows the power to reach a stable level before normal operation starts. The time-out
period of the delay counter is defined by the user through the SUT and CKSEL Fuses. The dif-
ferent selections for the delay period are presented in
The AT90USB64/128 has five sources of reset:
• Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset
• External Reset. The MCU is reset when a low level is present on the RESET pin for longer
• Watchdog Reset. The MCU is reset when the Watchdog Timer period expires and the
• Brown-out Reset. The MCU is reset when the supply voltage V
• JTAG AVR Reset. The MCU is reset as long as there is a logic one in the Reset Register, one
threshold (V
than the minimum pulse length.
Watchdog is enabled.
Reset threshold (V
of the scan chains of the JTAG system. Refer to the section
scan” on page 341
Table 8-1
POT
defines the electrical parameters of the reset circuitry.
).
BOT
for details.
) and the Brown-out Detector is enabled.
“Clock Sources” on page
“IEEE 1149.1 (JTAG) Boundary-
CC
Figure 8-1
is below the Brown-out
39.
shows the reset
7593A–AVR–02/06
Related parts for AT90USB1286-16MU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MCU, MPU & DSP Development Tools Demo board f/AVR MCU & AT90USB
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: