DS2155LC1 Maxim Integrated, DS2155LC1 Datasheet - Page 203
![no-image](/images/no-image-200.jpg)
DS2155LC1
Manufacturer Part Number
DS2155LC1
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS2155GNB.pdf
(238 pages)
- Current page: 203 of 238
- Download datasheet (2Mb)
Table 34-A. Instruction Codes for IEEE 1149.1 Architecture
SAMPLE/PRELOAD
This is a mandatory instruction for the IEEE 1149.1 specification that supports two functions. The digital
I/Os of the device can be sampled at the boundary scan register without interfering with the normal
operation of the device by using the Capture-DR state. SAMPLE/PRELOAD also allows the device to
shift data into the boundary scan register through JTDI using the Shift-DR state.
BYPASS
When the BYPASS instruction is latched into the parallel instruction register, JTDI connects to JTDO
through the 1-bit bypass test register. This allows data to pass from JTDI to JTDO without affecting the
device’s normal operation.
EXTEST
This allows testing of all interconnections to the device. When the EXTEST instruction is latched in the
instruction register, the following actions occur: Once enabled through the Update-IR state, the parallel
outputs of all digital output pins are driven. The boundary scan register is connected between JTDI and
JTDO. The Capture-DR samples all digital inputs into the boundary scan register.
CLAMP
All digital outputs of the device output data from the boundary scan parallel output while connecting the
bypass register between JTDI and JTDO. The outputs do not change during the CLAMP instruction.
HIGHZ
All digital outputs of the device are placed in a high-impedance state. The BYPASS register is connected
between JTDI and JTDO.
IDCODE
When the IDCODE instruction is latched into the parallel instruction register, the identification test
register is selected. The device identification code is loaded into the identification register on the rising
edge of JTCLK following entry into the Capture-DR state. Shift-DR can be used to shift the identification
code out serially through JTDO. During Test-Logic-Reset, the identification code is forced into the
instruction register’s parallel output. The ID code always has a 1 in the LSB position. The next 11 bits
identify the manufacturer’s JEDEC number and number of continuation bytes followed by 16 bits for the
device and 4 bits for the version
SAMPLE/PRELOAD
INSTRUCTION
BYPASS
IDCODE
EXTEST
CLAMP
HIGHZ
SELECTED REGISTER
Device Identification
Boundary Scan
Boundary Scan
(Table
Bypass
Bypass
Bypass
34-B).
Table 34-C
203 of 238
INSTRUCTION CODES
lists the device ID codes for the SCT devices.
010
111
000
011
100
001
Related parts for DS2155LC1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![DS2155](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Manufacturer:
Maxim Integrated Products
Datasheet:
![ds2155gt-r](/images/no-image3.png)
Part Number:
Description:
Ds2155 T1/e1/j1 Single-chip Transceiver
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products