FPS100024 TDK Corporation, FPS100024 Datasheet - Page 22

• Manufacturer Part Number: FPS100024
• Description: PWR SUP FNT END 24V 960W 40A
• Manufacturer: TDK Corporation
• Series: FPSr
• Type: Commercialr

Specifications of FPS100024

• Power Supply Type: Switching (Closed Frame)
• Voltage - Output: 24V
• Number Of Outputs: 1
• Power (watts): 1000W
• Applications: Commercial
• Voltage - Input: 85 ~ 265VAC
• Mounting Type: Chassis Mount
• 1st Output: 24 VDC @ 40A
• Size / Dimension: 1.61" L x 5" W x 11.4" H (40.9mm x 127mm x 289.6mm)
• Power (watts) - Rated: 960W
• Operating Temperature: 0°C ~ 70°C
• Efficiency: 86%
• Approvals: CE, EN, UL
• Line Regulation: 0.4%
• Load Regulation: 0.8%
• Power Supply Output Type: Fixed
• No. Of Outputs: 1
• Output Voltage: 24V
• Output Current: 40A
• Power Rating: 960W
• Input Voltage: 85V AC - 265V AC / 120V DC To 360V DC.
• Brand/series: FPS1000 Series
• Configuration: Enclosed
• Operation: Linear
• Output: 24 VDC @ 40 A
• Power, Output: 960 W
• Primary Type: AC-DC
• Special Features: High Efficiency, Hot Swappable, PFC, Remote On/Off, Remote Sense
• Voltage, Input: 85 to 265/120 to 360 VAC/VDC
• Voltage, Output: 24 VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1237

CHAPTER 7
7.1 Introduction
The I
are then transferred to the host PC if demanded, over a standard I
The following data can be monitored for the individual units connected to the I
1. Status of the unit.
2. Actual output voltage, output current and internal temperature of the unit.
3. Manufacturing related data (model, serial number, manufacturing date etc…).
7.1.1 Addressing (A0, A1, A2).
Three address lines allow up to eight FPS1000 units to be addressed on a single I
internally pulled-up to +5V by resistors. Addressing of a unit is achieved by hard-wiring an address line to the
-Sense to set it to "0" or leaving the address line open to set it to "1".
7.1.2 Serial clock
This line is clocked by the processor which controls the I
via a pull-up resistor of 2KΩ. The I
7.1.3 Serial dataThis line is a bidirectional data line. It should be connected to +5V
(referenced to -Sense) via a pull-up resistor of 2KΩ.
7.2 I
7.2.1 General specifications
1. Clock frequency:
2. Address lines:
7.2.2 Output voltage measurement
1. Measurement accuracy:
2. Measurement resolution:
3. Measurement range:
7.2.3 Output current measurement
1. Measurement accuracy:
2. Measurement resolution:
3. Measurement range:
7.2.4 Internal temperature measurement
1. Measurement accuracy:
2. Measurement resolution:
3. Measurement range:
7.2.5 EEPROM
1. EEPROM type:
2. EEPROM data:
7.2.6 Status register
1. Register type:
2. Register content:
2
2
C Interface Specifications
C interface option includes facilities to monitor operating parameters of the power supply. The parameters
I
2
C BUS INTERFACE OPTION
The I
referenced to the -Sense potential. When using series
connection of FPS1000 units, do not connect the I
of the units together.
2
C interface is designed to run with a serial clock speed of 100KHz.
2
C bus address lines, serial clock and data are
0~60.0V for 48V model / 0~40.0V for 32V model / 0-30.0V for 24V model.
100KHz
Three (A0, A1, A2). Support 8 power supply modules
+/-2% of full scale
8 bits
+/-10% of full scale
8 bits
+/-3°C
8 bits
0-100°C
AT24C02AN-10S , Atmel, or equivalent
Model name, Serial no., Revision, Manufacture. Name, Output voltage,
Date, Country of manufacturing, Check-Sum
PCF8574, Philips, or equivalent.
DC Fail, Over-Temperature Protection (OTP)
Temperature Alarm, Fan Fail, AC Fail
0~25.0A for 48V model / 0~50A for 32V & 24V models
CAUTION
2
C bus. It should be connected to +5V (referenced to -Sense)
19
2
C bus.
2
FPS1000 Instruction Manual
C bus:
2
2
C lines
C bus. The address lines are