FPS100024 TDK Corporation, FPS100024 Datasheet - Page 36

• Manufacturer Part Number: FPS100024
• Description: PWR SUP FNT END 24V 960W 40A
• Manufacturer: TDK Corporation
• Series: FPSr
• Type: Commercialr

Specifications of FPS100024

• Power Supply Type: Switching (Closed Frame)
• Voltage - Output: 24V
• Number Of Outputs: 1
• Power (watts): 1000W
• Applications: Commercial
• Voltage - Input: 85 ~ 265VAC
• Mounting Type: Chassis Mount
• 1st Output: 24 VDC @ 40A
• Size / Dimension: 1.61" L x 5" W x 11.4" H (40.9mm x 127mm x 289.6mm)
• Power (watts) - Rated: 960W
• Operating Temperature: 0°C ~ 70°C
• Efficiency: 86%
• Approvals: CE, EN, UL
• Line Regulation: 0.4%
• Load Regulation: 0.8%
• Power Supply Output Type: Fixed
• No. Of Outputs: 1
• Output Voltage: 24V
• Output Current: 40A
• Power Rating: 960W
• Input Voltage: 85V AC - 265V AC / 120V DC To 360V DC.
• Brand/series: FPS1000 Series
• Configuration: Enclosed
• Operation: Linear
• Output: 24 VDC @ 40 A
• Power, Output: 960 W
• Primary Type: AC-DC
• Special Features: High Efficiency, Hot Swappable, PFC, Remote On/Off, Remote Sense
• Voltage, Input: 85 to 265/120 to 360 VAC/VDC
• Voltage, Output: 24 VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1237

12.4 On/Off control
Fig 12-4 shows typical connection for individual On/Off control of each installed FPS1000 unit. The On/Off
control signal is applied to the DB25 connector located at the rear panel (refer to sec. 10.7.5).
When it is desired to control all the installed units simultaneously, it is possible to connect the On/Off control
as shown in Fig 12-5.
Fig 12-4: Individual On/Off control
12.5 Output voltage trimming
Refer to Fig 12-6 for output voltage trimming typical application.
12.6 Supervisory signals
Supervisory signals are accessible at the J1-DB25 female connector on the rear panel of the rack.
Fig 12-7 shows a typical connection for FPS1000 unit "A" inside the rack.
Units "B" and "C" connections - Reffer to sec 10.7.5.
12.7 Grounding outputs
Either the positive or negative output terminals can be grounded. To avoid noise problems caused by
common-mode current flowing from the load to ground, it is recommended to ground the output terminal
as close as possible to the power supply's output. Always use two wires to connect the load to the power
supply regardless of how the system is grounded.
FPS-S1U
Note: AC_FAIL, DC_OK and TEMP.ALARM are open collector signals.
Fig 12-7: Supervisory signals
Fig 12-6: Output voltage trimming
FPS-S1U
FPS-1000
Module A
FPS-1000 Module B
FPS-1000 Module C
FPS-S1U
SIGNAL_RET
ON/OFF_A
ON/OFF_B
ON/OFF_C
TEMP.ALARM_A
V_TRIM_A
V_TRIM_B
V_TRIM_C
SIGNAL RET
AC_FAIL_A
DC_OK_A
12V AUX
15
25
11
+S
5
-S
ON/
OFF
UNIT
‘C’
13
7
1
10
22
ON/
OFF
(J1)
16
11
8
6
4
UNIT
+V
-V
‘B’
10K
ON/
OFF
UNIT
‘A’
10K
R1
R2
10K
FPS-S1U
Fig 12-5: Single On/Off control
FPS-S1U with FPS1000-12 installed:
R2=0.0324*V
R1(K Ω )=5(K Ω )-R2(K Ω )
FPS-S1U with FPS1000-24 installed:
R2=0.0785*V
R1(K Ω )=20(K Ω )-R2(K Ω )
FPS-S1U with FPS1000-32 installed:
R2=0.0463*V
FPS-S1U with FPS1000-48 installed:
R2=0.0497*V
R1(K Ω )=50(K Ω )-R2(K Ω )
R1(K Ω )=20(K Ω )-R2(K Ω Ω)
Application
Monitoring
and Control
circuts
33
SIGNAL_RET
ON/OFF_A
ON/OFF_B
ON/OFF_C
2
2
2
2
out
out
out
out
-7.2795*V
-1.1298*V
-5.819*V
-4.5805*V
15
25
11
5
ON/
OFF
out
out
FPS-S1U Instruction Manual
out
out
+105.132
+259.04
+9.9342
+109.49