FPS100024 TDK Corporation, FPS100024 Datasheet - Page 29

• Manufacturer Part Number: FPS100024
• Description: PWR SUP FNT END 24V 960W 40A
• Manufacturer: TDK Corporation
• Series: FPSr
• Type: Commercialr

Specifications of FPS100024

• Power Supply Type: Switching (Closed Frame)
• Voltage - Output: 24V
• Number Of Outputs: 1
• Power (watts): 1000W
• Applications: Commercial
• Voltage - Input: 85 ~ 265VAC
• Mounting Type: Chassis Mount
• 1st Output: 24 VDC @ 40A
• Size / Dimension: 1.61" L x 5" W x 11.4" H (40.9mm x 127mm x 289.6mm)
• Power (watts) - Rated: 960W
• Operating Temperature: 0°C ~ 70°C
• Efficiency: 86%
• Approvals: CE, EN, UL
• Line Regulation: 0.4%
• Load Regulation: 0.8%
• Power Supply Output Type: Fixed
• No. Of Outputs: 1
• Output Voltage: 24V
• Output Current: 40A
• Power Rating: 960W
• Input Voltage: 85V AC - 265V AC / 120V DC To 360V DC.
• Brand/series: FPS1000 Series
• Configuration: Enclosed
• Operation: Linear
• Output: 24 VDC @ 40 A
• Power, Output: 960 W
• Primary Type: AC-DC
• Special Features: High Efficiency, Hot Swappable, PFC, Remote On/Off, Remote Sense
• Voltage, Input: 85 to 265/120 to 360 VAC/VDC
• Voltage, Output: 24 VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1237

CHAPTER 10
10.1 GENERAL
This chapter contains instructions for initial inspection, preparation for use and repackaging for shipment.
In some sections in this chapter, where the instructions for the FPS-S1U and the FPS1000 are identical,
a reference to a section describing the FPS1000 will be given.
10.2 PREPARATION FOR USE
Table 10-1 below describes the basic setup procedure. Follow the instructions in Table 10-1 in the sequence
given to prepare the FPS-S1U rack for use.
10.3 INITIAL INSPECTION
Refer to Sec. 3.3 for details.
10.4 FPS-S1U RACK MOUNTING
The FPS-S1U is designed to be mounted in a 19" rack. Use a support bars or surface to provide adequate
support for the rear of the power supply. Secure the FPS-S1U to its location using the front panel using
M6x12 screws via the mounting holes at its front side (Refer to the outline drawings in Chapter 11).
Do not obstruct the air exhaust at the rear panel of the unit.
10.5 LOCATION MOUNTING AND COOLING
The FPS1000 units installed in the FPS-S1U rack are fan cooled. The air intake is at the front panel and
the exhaust is at the rear panel. Upon installation allow cooling air to reach the front panel and allow
minimum 50mm of unrestricted air space at the rear of the unit for the air exhaust.
10.6 AC SOURCE REQUIREMENTS
Refer to Sect 3.6 for details.
10.7 CONNECTING THE LOAD
10.7.1 Load Wiring
.Refer to Sec. 3.7.1, 3.7.2 and 3.7.3 for details.
10.7.2 Inductive loads
To prevent damage to the power supply from inductive kickback, a diode should be connected across the
output. The diode voltage and current rating should be greater than the power supply maximum output
voltage and total current rating. Connect the cathode to the positive output and the anode to the negative
output. Where positive load transients such as back EMF from a motor may occur, connect a surge
suppressor across the output to protect the power supply. The breakdown voltage rating of the suppressor
must be approximately 10% higher than the maximum output voltage of the power supply.
Step no Item
1
2
3
4
Table 10-1: Basic setup procedure
Ensure that all connections are securely tightened before applying power. There is a
potential shock hazard when using a power supply with a rated output greater than 40V.
Inspection
Installation
AC source
Load connection
Turn off the AC input power before making or changing any rear panel connection.
FPS-S1U RACK INSTALLATION
Description
Initial physical inspection of the power supply
Installing the power supply.
Ensuring adequate ventilation.
AC source requirements
Wire size selection.
WARNING
26
Section 3.3
Section 10.4
Section 10.5
Section 3.6
Section 10.7
Reference