CY8CKIT-006 Cypress Semiconductor Corp, CY8CKIT-006 Datasheet - Page 20

• Manufacturer Part Number: CY8CKIT-006
• Description: KIT DEV PSOC3 LCD SEGMENT
• Manufacturer: Cypress Semiconductor Corp
• Series: PSOC™ 3r

Specifications of CY8CKIT-006

• Main Purpose: Displays, LCD Display
• Embedded: Yes, MCU, 32-Bit
• Primary Attributes: 448 addressable segments
• Secondary Attributes: Configurable LCD pin selection
• Description/function: Evaluation Kit
• Interface Type: USB
• Backlighting: No Backlighting
• Data Bus Width: 8 bit, 16 bit, 32 bit
• Maximum Operating Temperature: + 50 C
• Minimum Operating Temperature: 0 C
• Number Of Segments: 7
• Operating Supply Voltage: 12 V
• Operating Voltage: 3.3 V
• Pixel Format: 16 x 28
• Product: Display Modules
• Software: Software Included
• Touch Panel: No Touch Panel
• For Use With/related Products: PSoC 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Utilized Ic / Part: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-2994

Hardware
4.2
20
Operation Theory - All Components
1
2
3
4
5
6
7
8
9
10
Sl. No.
Slide Switch (SW1)
Pushbutton Switch (S1)
LCD Glass (P1)
CapSense Buttons:
CSD1 (Labeled as ‘+’)
CSD2 (Labeled as ‘RET’)
CSD3 (Labeled as ‘-‘)
CSD4 (Labeled as ‘SEL’)
Accelerometer (Memsic
MXR2010A (U12))
Buzzer(CUI CMT -1603
(LSI))
Thermistor (RT1)
RTC Crystal (Y1)
GPIO Connector(J4)
JTAG MiniProg3 Connector
(J1)
Device Features
CY8CKIT-006 PSoC 3 LCD Segment Drive Evaluation Kit Guide, Doc. # 001-52798 Rev. *C
This switch turns the power supplied by the battery On and Off.
Note Switch (SW1) does not control the power supplied by
sources through J1(USB) and J2(Wall Power).
This switch is used to enter (Switch - On) and exit (Switch-Off) the
sleep modes.
Note The project supports all the sleep features described with the
exception that PSoC 3 device does not go to sleep; the firmware is
just put in a low power mode.
Provides visual feedback. Custom made glass with 448 segments.
Refer to
CapSense buttons are used to navigate through various modes of
operation.
Table 3-1 on page
for each mode of operation.
The dual axis accelerometer is used to detect the movement and
calculate the force of a punch.
Accelerometer has a range of ±35G at 5V/25°C and can measure
both static and dynamic acceleration.
It provides audible feedback to the user.
A 5V, 4 kHz square wave is applied to the buzzer’s input to pro-
duce sound.
It is used to detect the ambient temperature for use in the Time/
Temp demonstration mode.
The default firmware supports a 10k thermistor rated to ±0.75% at
25°C.
This external crystal is used as a 32.768 kHz clock source for
maintaining real-time operation in the Time/Temp demonstration
mode.
The header (J4) provides 3 SIO, 2 GPIO, XRES, VDD, and GND
signals, thereby facilitating users to develop their own application.
Refer to Hardware Schematic and PSoC 3 data sheet for specific
details regarding the SIO and GPIO pins connected to these sig-
nals.
The J1 connector provides a programming and debugs connection
between the PSoC 3 and MiniProg3 programmer.
Note Miniprog3 can be used to supply the power to the board for
programming, but this is not recommended for normal or debugs
operation.
LCD Glass on page 21
9, explains the function of CapSense buttons
Description
for glass details.
[+] Feedback