MPC564MZP56 Freescale Semiconductor, MPC564MZP56 Datasheet - Page 1034

• Manufacturer Part Number: MPC564MZP56
• Description: IC MCU 512K FLASH 56MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Core: PowerPC
• Processor Series: MPC5xx
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 56 MHz
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 56
• Number Of Timers: 2
• Operating Supply Voltage: 0 V to 5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 32
• Height: 1.95 mm
• Interface Type: CAN, JTAG, QSPI, SCI, SPI, UART
• Length: 27 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 2.7 V, 5.25 V
• Supply Voltage (min): 2.5 V, 4.75 V
• Width: 27 mm
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

READI Module
L-bus data error conditions are signalled along with the transfer acknowledge for the access. L-bus data
error conditions may occur because of privilege violations, access to protected memory, etc. In such cases,
for a read access, the ERR bit of the UDI is set, and the DV bit in the UDI is reset at the termination of the
access. For a write access, an error public message (TCODE = 8) is transmitted (error code 0b00011).
24.10.6 Exception Sequences
The following cases are defined for sequences of the read/write protocol that differ from those described
in the above sections:
24.10.7 Secure Mode
For details refer to
24.10.8 Error Messages
24.10.8.1 Read/Write Access Error
An error message is sent out when an L-bus access error or data error on a write access occurs. The error
code within the error message indicates that an L-bus address or L-bus data error occurred. For other error
handling, see
24-66
•
•
•
1. If the SC bit is set to start READI read/write accesses, without valid values in the RWAD, then an
2. If a block access is in progress with all the cycles not yet completed, and the RWA is written to
3. When a block access is in progress with all the cycles not yet completed, writing the SC bit to 0 in
4. If a any type (single/block) of access is in progress with the cycles not yet completed, and system
5. If any type of (single/block) of access is requested while system is in reset, the device will send out
L-bus data phase error.
U-bus address phase error (for a L-bus to U-bus cycle).
U-bus data phase error (for a L-bus to U-bus cycle).
L-bus address error may occur, which is handled as described above.
again, (with or without modifications), then the block access is terminated at the boundary of the
nearest completed access. The resulting data is discarded and not written to the UDI. If a new
access has been programmed in the RWA register, then that access will start once the controller has
recovered.
RWA register will terminate the block access and device will send out device ready for
upload/download message.
reset occurs, the device will send out an error message. The access will be terminated and the SC
bit will be reset. Refer to
an error message. The access will not be started and the SC bit will be reset.
Section 24.10.5, “Error
Section 24.2.2,
MPC561/MPC563 Reference Manual, Rev. 1.2
Table
“Security.”
Handling.” For a list of error codes, refer to
24-20.
Table
Freescale Semiconductor
24-20.