ST10F276-6QR3 STMicroelectronics, ST10F276-6QR3 Datasheet - Page 173

• Manufacturer Part Number: ST10F276-6QR3
• Description: MCU 16BIT 832K FLASH 144-PQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10F276-6QR3

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 64MHz
• Connectivity: ASC, CAN, EBI/EMI, I²C, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 832KB (832K x 8)
• Program Memory Type: FLASH
• Ram Size: 68K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-MQFP, 144-PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

ST10F276E
Note:
22.12
The default XPER selection after Reset is such that CAN1 is enabled, CAN2 is disabled,
XRAM1 (2 Kbyte XRAM) is enabled and XRAM2 (64 Kbyte XRAM) is disabled; all the other
X-Peripherals are disabled after Reset.
Register XPERCON cannot be changed after the global enabling of X-Peripherals, that is,
after setting of bit XPEN in SYSCON register.
In Emulation mode, all the X-Peripherals are enabled (XPERCON bits are all set). The
bondout chip determines whether or not to redirect an access to external memory or to
XBUS.
Reserved bits of XPERCON register are always written to ‘0’.
Table 85
during reset as well as the SYSCON (bit XPEN) and XPERCON (bits XRAM2EN and
XFLASHEN) registers user programmed values.
Table 85.
The symbol “x” in the table above stands for “do not care”.
XPERCON and XPEREMU registers
As already mentioned, the XPERCON register must be programmed to enable the single
XBUS modules separately. The XPERCON is a read/write ESFR register; the XPEREMU
register is a write-only register mapped on XBUS memory space (address EB7Eh).
Once the XPEN bit of SYSCON register is set and at least one of the X-peripherals (except
memories) is activated, the register XPEREMU must be written with the same content of
XPERCON: This is mandatory in order to allow a correct emulation of the new set of
features introduced on XBUS for the new ST10 generation. The following instructions must
be added inside the initialization routine:
Of course, XPEREMU must be programmed after XPERCON and after SYSCON; in this
way the final configuration for X-Peripherals is stored in XPEREMU and used for the
emulation hardware setup.
XPEREMU (EB7Eh)
.
15
-
-
if (SYSCON.XPEN && (XPERCON & 0x07D3))
then { XPEREMU = XPERCON }
EA
0
0
0
0
1
14
-
-
below summarizes the Segment 8 mapping that depends upon the EA pin status
Segment 8 address range mapping
13
-
-
XPEN
12
-
-
0
1
1
1
x
11
-
-
XMISC
XRAM2EN
RW
10
EN
x
0
1
x
x
XI2C
RW
EN
9
XBUS
XSSC
RW
EN
8
XFLASHEN
XASC
RW
EN
x
0
x
1
x
7
XPWM
RW
EN
6
External memory
External memory
Reserved
Reserved
IFlash (B1F1)
XFLAS
HEN
RW
5
XRTC
RW
EN
4
Segment 8
XRAM2
RW
EN
3
Reset value xxxxh:
XRAM1
RW
EN
2
Register set
CAN2
RW
EN
1
173/231
CAN1
RW
EN
0