MCF5280CVM66 Freescale Semiconductor, MCF5280CVM66 Datasheet - Page 467

• Manufacturer Part Number: MCF5280CVM66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5280CVM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• No. Of I/o's: 150
• Program Memory Size: 2KB
• Ram Memory Size: 64KB
• Cpu Speed: 66.67MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

processor may need to wait until the I2C is busy after writing the calling address to the I2DR before
proceeding with the following instructions.
The following example signals START and transmits the first byte of data (slave address):
24.4.3
Sending or receiving a byte sets the I2SR[ICF], which indicates one byte communication is finished.
I2SR[IIF] is also set. An interrupt is generated if the interrupt function is enabled during initialization by
setting I2CR[IIEN]. Software must first clear I2SR[IIF] in the interrupt routine. Reading from I2DR in
receive mode or writing to I2DR in transmit mode can clear I2SR[ICF].
Software can service the I
disabled. Polling should monitor IIF rather than ICF, because that operation is different when arbitration
is lost.
When an interrupt occurs at the end of the address cycle, the master is always in transmit mode; the address
is sent. If master receive mode is required, I2CR[MTX] should be toggled.
During slave-mode address cycles (I2SR[IAAS] = 1), I2SR[SRW] is read to determine the direction of the
next transfer. MTX is programmed accordingly. For slave-mode data cycles (IAAS = 0), SRW is invalid.
MTX should be read to determine the current transfer direction.
The following is an example of a software response by a master transmitter in the interrupt routine (see
Figure
24.4.4
A data transfer ends when the master signals a STOP, which can occur after all data is sent, as in the
following example.
Freescale Semiconductor
1. Check I2SR[IBB]. If it is set, wait until it is clear.
2. After cleared, set to transmit mode by setting I2CR[MTX].
3. Set master mode by setting I2CR[MSTA]. This generates a START condition.
4. Transmit the calling address via the I2DR.
5. Check I2SR[IBB]. If it is clear, wait until it is set and go to step #1.
1. Clear the I2CR[IIF] flag.
2. Check if acknowledge has been received, I2SR[RXAK].
3. If no ACK, end transmission. Else, transmit next byte of data via I2DR.
1. Check if acknowledge has been received, I2SR[RXAK]. If no ACK, end transmission and go to
2. Get value from transmitting counter, TXCNT. If no more data, go to step #5.
3. Transmit next byte of data via I2DR.
4. Decrement TXCNT and go to step #1
5. Generate a stop condition by clearing I2CR[MSTA].
24-14).
step #5.
Post-Transfer Software Response
Generation of STOP
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
2
C I/O in the main program by monitoring the IIF bit if the interrupt function is
I
2
C Interface
24-13