PIC16F690-E/ML Microchip Technology, PIC16F690-E/ML Datasheet - Page 214

• Manufacturer Part Number: PIC16F690-E/ML
• Description: IC, 8BIT MCU, PIC16F, 20MHZ, QFN-20
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F690-E/ML

• Controller Family/series: PIC16F
• No. Of I/o's: 18
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Core Size: 8 Bit
• Program Memory Size: 4096 Words
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-VQFN Exposed Pad, 20-HVQFN, 20-SQFN, 20-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20QFN-1 - SOCKET TRANSITION 20DIP-20QFNAC164324 - MODULE SKT FOR MPLAB 8DFN/16QFNPIC16F690DM-PCTLHS - BOARD DEMO PICTAIL HUMIDITY SNSRAC162061 - HEADER INTRFC MPLAB ICD2 20PIN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F631/677/685/687/689/690
14.5
The WDT has the following features:
• Operates from the LFINTOSC (31 kHz)
• Contains a 16-bit prescaler
• Shares an 8-bit prescaler with Timer0
• Time-out period is from 1 ms to 268 seconds
• Configuration bit and software controlled
WDT is cleared under certain conditions described in
Table 14-7.
14.5.1
The WDT derives its time base from the 31 kHz
LFINTOSC. The LTS bit of the OSCCON register does
not reflect that the LFINTOSC is enabled.
The value of WDTCON is ‘---0 1000’ on all Resets.
This gives a nominal time base of 17 ms.
FIGURE 14-9:
TABLE 14-7:
DS41262E-page 212
WDTE = 0
CLRWDT Command
Oscillator Fail Detected
Exit Sleep + System Clock = T1OSC, EXTRC, INTOSC, EXTCLK
Exit Sleep + System Clock = XT, HS, LP
LFINTOSC Clock
Note:
Note 1:
31 kHz
Watchdog Timer (WDT)
WDT OSCILLATOR
When the Oscillator Start-up Timer (OST)
is invoked, the WDT is held in Reset,
because the WDT Ripple Counter is used
by the OST to perform the oscillator delay
count. When the OST count has expired,
the WDT will begin counting (if enabled).
This is the shared Timer0/WDT prescaler. See Section 5.4 “Prescaler” for more information.
WDT STATUS
WATCHDOG TIMER BLOCK DIAGRAM
WDTE from the Configuration Word Register
SWDTEN from WDTCON
Conditions
16-bit WDT Prescaler
WDTPS<3:0>
From TMR0 Clock Source
14.5.2
The WDTE bit is located in the Configuration Word
register. When set, the WDT runs continuously.
When the WDTE bit in the Configuration Word register
is set, the SWDTEN bit of the WDTCON register has no
effect. If WDTE is clear, then the SWDTEN bit can be
used to enable and disable the WDT. Setting the bit will
enable it and clearing the bit will disable it.
The PSA and PS<2:0> bits of the OPTION register
have the same function as in previous versions of the
PIC16F631/677/685/687/689/690 Family of microcon-
trollers. See Section 5.0 “Timer0 Module” for more
information.
0
1
WDT CONTROL
PSA
Cleared until the end of OST
WDT Time-out
© 2008 Microchip Technology Inc.
0
Prescaler
Cleared
1
8
WDT
(1)
PSA
PS<2:0>
To TMR0