AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 78

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.1.9
10.2
10.2.1
32072G–11/2011
Rev. E
FLASHC
General
Processor and Architecture
Corrupted read in flash may happen after fuses write or erase operations (FLASHC
LP, UP, WGPB, EGPB, SSB, PGPFB, EAGPF commands)
After a flash fuse write or erase operation (FLASHC LP, UP, WGPB, EGPB, SSB, PGPFB,
EAGPF commands), reading (data read or code fetch) in flash may fail. This may lead to an
exception or to other errors derived from this corrupted read access.
Fix/Workaround
Before the flash fuse write or erase operation, enable the flash high speed mode (FLASHC
HSEN command). The flash fuse write or erase operations (FLASHC LP, UP, WGPB,
EGPB, SSB, PGPFB, EAGPF commands) must be issued from RAM or through the EBI.
After these commands, read 3 times one flash page initialized to 00h. Disable the flash high
speed mode (FLASHC HSDIS command). It is then possible to safely read or code fetch the
flash.
Increased Power Consumption in VDDIO in sleep modes
If the OSC0 is enabled in crystal mode when entering a sleep mode where the OSC0 is dis-
abled, this will lead to an increased power consumption in VDDIO.
Fix/Workaround
Disable the OSC0 through the System Control Interface (SCIF) before going to any sleep
mode where the OSC0 is disabled, or pull down or up XIN0 and XOUT0 with 1 Mohm
resistor.
Power consumption in static mode The power consumption in static mode can be up
to 330µA on some parts (typical at 25°C)
Fix/Workaround
Set to 1b bit CORRS4 of the ECCHRS mode register (MD). In C-code: *((volatile int*)
(0xFFFE2404))= 0x400.
DMACA
CTLx.DST_TR_WIDTH
Fix/Workaround
For any DMACA transfer make sure CTLx.SRC_TR_WIDTH = CTLx.DST_TR_WIDTH.
3.3V supply monitor is not available
FGPFRLO[30:29] are reserved and should not be used by the application.
Fix/Workaround
None.
Service access bus (SAB) can not access DMACA registers
Fix/Workaround
None.
LDM instruction with PC in the register list and without ++ increments Rp
For LDM with PC in the register list: the instruction behaves as if the ++ field is always set, ie
the pointer is always updated. This happens even if the ++ field is cleared. Specifically, the
increment of the pointer is done in parallel with the testing of R12.
data
transfer
fails
when
CTLx.SRC_TR_WIDTH
is
not
equal
78
to