C8051F331-GM Silicon Laboratories Inc, C8051F331-GM Datasheet - Page 138
![IC 8051 MCU 8K FLASH 20QFN](/photos/12/16/121620/c8051f331-gm_sml.jpg)
C8051F331-GM
Manufacturer Part Number
C8051F331-GM
Description
IC 8051 MCU 8K FLASH 20QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051F33xr
Specifications of C8051F331-GM
Program Memory Type
FLASH
Program Memory Size
8KB (8K x 8)
Package / Case
20-QFN
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
17
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F3x
Core
8051
Data Bus Width
8 bit
Data Ram Size
768 B
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
17
Number Of Timers
4
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F330DK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 16 Channel
No. Of I/o's
17
Ram Memory Size
768Byte
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1451 - ADAPTER PROGRAM TOOLSTICK F330336-1264 - DEV KIT FOR C8051F330/F331
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1265
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F331-GM
Manufacturer:
SiliconL
Quantity:
1 630
Part Number:
C8051F331-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
C8051F331-GMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
C8051F330/1/2/3/4/5
142
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bits1–0: SMBCS1–SMBCS0: SMBus Clock Source Selection.
ENSMB
R/W
Bit7
ENSMB: SMBus Enable.
This bit enables/disables the SMBus interface. When enabled, the interface constantly mon-
itors the SDA and SCL pins.
0: SMBus interface disabled.
1: SMBus interface enabled.
INH: SMBus Slave Inhibit.
When this bit is set to logic 1, the SMBus does not generate an interrupt when slave events
occur. This effectively removes the SMBus slave from the bus. Master Mode interrupts are
not affected.
0: SMBus Slave Mode enabled.
1: SMBus Slave Mode inhibited.
BUSY: SMBus Busy Indicator.
This bit is set to logic 1 by hardware when a transfer is in progress. It is cleared to logic 0
when a STOP or free-timeout is sensed.
EXTHOLD: SMBus Setup and Hold Time Extension Enable.
This bit controls the SDA setup and hold times according to .
0: SDA Extended Setup and Hold Times disabled.
1: SDA Extended Setup and Hold Times enabled.
SMBTOE: SMBus SCL Timeout Detection Enable.
This bit enables SCL low timeout detection. If set to logic 1, the SMBus forces Timer 3 to
reload while SCL is high and allows Timer 3 to count when SCL goes low. If Timer 3 is con-
figured to Split Mode, only the High Byte of the timer is held in reload while SCL is high.
Timer 3 should be programmed to generate interrupts at 25 ms, and the Timer 3 interrupt
service routine should reset SMBus communication.
SMBFTE: SMBus Free Timeout Detection Enable.
When this bit is set to logic 1, the bus will be considered free if SCL and SDA remain high for
more than 10 SMBus clock source periods.
These two bits select the SMBus clock source, which is used to generate the SMBus bit
rate. The selected device should be configured according to Equation 15.1.
SMBCS1
SFR Definition 15.1. SMB0CF: SMBus Clock/Configuration
INH
R/W
Bit6
0
0
1
1
SMBCS0
BUSY
Bit5
R
0
1
0
1
EXTHOLD SMBTOE SMBFTE SMBCS1
R/W
Bit4
Timer 2 High Byte Overflow
Timer 2 Low Byte Overflow
SMBus Clock Source
Timer 0 Overflow
Timer 1 Overflow
Rev. 1.7
R/W
Bit3
R/W
Bit2
R/W
Bit1
SFR Address:
SMBCS0 00000000
R/W
Bit0
0xC1
Reset Value