C8051F331-GM Silicon Laboratories Inc, C8051F331-GM Datasheet - Page 150
![IC 8051 MCU 8K FLASH 20QFN](/photos/12/16/121620/c8051f331-gm_sml.jpg)
C8051F331-GM
Manufacturer Part Number
C8051F331-GM
Description
IC 8051 MCU 8K FLASH 20QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051F33xr
Specifications of C8051F331-GM
Program Memory Type
FLASH
Program Memory Size
8KB (8K x 8)
Package / Case
20-QFN
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
17
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F3x
Core
8051
Data Bus Width
8 bit
Data Ram Size
768 B
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
17
Number Of Timers
4
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F330DK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 16 Channel
No. Of I/o's
17
Ram Memory Size
768Byte
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1451 - ADAPTER PROGRAM TOOLSTICK F330336-1264 - DEV KIT FOR C8051F330/F331
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1265
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F331-GM
Manufacturer:
SiliconL
Quantity:
1 630
Part Number:
C8051F331-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
C8051F331-GMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
C8051F330/1/2/3/4/5
16.1. Enhanced Baud Rate Generation
The UART0 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 16.2), which is not user-
accessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud rates.
The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see
ter/Timer with Auto-Reload” on page 179
occur at two times the desired UART baud rate frequency. Note that Timer 1 may be clocked by one of six
sources: SYSCLK, SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, the external oscillator clock / 8, or an exter-
nal input T1. For any given Timer 1 clock source, the UART0 baud rate is determined by Equation 16.1-A
and Equation 16.1-B.
Where T1
value). Timer 1 clock frequency is selected as described in
reference for typical baud rates and system clock frequencies is given in Table 16.1 through Table 16.6.
Note that the internal oscillator may still generate the system clock when the external oscillator is driving
Timer 1.
154
CLK
is the frequency of the clock supplied to Timer 1, and T1H is the high byte of Timer 1 (reload
Detected
Start
A)
B)
Figure 16.2. UART0 Baud Rate Logic
UartBaudRate
T1_Overflow_Rate
RX Timer
Equation 16.1. UART0 Baud Rate
Timer 1
TH1
TL1
). The Timer 1 reload value should be set so that overflows will
=
Overflow
Overflow
Rev. 1.7
1
-- -
2
=
T1_Overflow_Rate
------------------------- -
256 TH1
T1
–
Section “18. Timers” on page 177
CLK
2
2
Section “18.1.3. Mode 2: 8-bit Coun-
UART
RX Clock
TX Clock
. A quick