MC9S08JM60CGT Freescale Semiconductor, MC9S08JM60CGT Datasheet - Page 248

• Manufacturer Part Number: MC9S08JM60CGT
• Description: IC MCU 8BIT 60K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM60CGT

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 37
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 24MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: QFN EP
• Package: 48QFN EP
• Family Name: HCS08
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• For Use With: DEMOJM - KIT DEMO FOR JM MCU FAMILYDEMOJMSKT - BOARD DEMO S08JM CARD W/SOCKET
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Serial Peripheral Interface (S08SPI16V1)
15.2
The SPI optionally shares four port pins. The function of these pins depends on the settings of SPI control
bits. When the SPI is disabled (SPE = 0), these four pins revert to being general-purpose port I/O pins that
are not controlled by the SPI.
15.2.1
When the SPI is enabled as a slave, this pin is the serial clock input. When the SPI is enabled as a master,
this pin is the serial clock output.
248
BUS RATE
CLOCK
SPI SYSTEM
SPIMODE
ENABLE
LSBFE
MSTR
SPE
External Signal Description
SPSCK — SPI Serial Clock
CLOCK GENERATOR
SPIBR
MASTER/SLAVE
MODE SELECT
SHIFT
OUT
8 OR 16
BIT MODE
SHIFT
DIRECTION
Tx BUFFER (WRITE SPIxDH:SPIxDL)
Rx BUFFER (READ SPIxDH:SPIxDL)
MODE FAULT
DETECTION
CLOCK
CLOCK
LOGIC
SHIFT
Figure 15-4. SPI Module Block Diagram
SPI SHIFT REGISTER
MODF
MC9S08JM60 Series Data Sheet, Rev. 3
Rx BUFFER
SPRF
FULL
Tx BUFFER
EMPTY
SHIFT
SPTEF
SPTIE
SPIE
IN
MASTER CLOCK
SLAVE CLOCK
16-BIT COMPARATOR
BIDIROE
MODFEN
SPC0
SSOE
SPIxMH:SPIxML
16-BIT LATCH
PIN CONTROL
M
S
M
S
M
S
MASTER/
SLAVE
Freescale Semiconductor
SPMIE
SPMF
SPI
INTERRUPT
REQUEST
MOSI
(MOMI)
MISO
(SISO)
SPSCK
SS