MC9S08DZ60ACLF Freescale Semiconductor, MC9S08DZ60ACLF Datasheet - Page 413

• Manufacturer Part Number: MC9S08DZ60ACLF
• Description: IC MCU 60K FLASH 4K RAM 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08DZ60ACLF

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 39
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: S08DZ
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 2
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• For Use With: DEMO9S08DZ60 - BOARD DEMOEVB9S08DZ60 - BOARD EVAL FOR 9S08DZ60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

end the trace run that was in progress. The ARMF bit is also cleared if ARM is written to zero or when the
DBGEN bit is low. The TBC logic determines whether a trigger condition has been met based on the
trigger mode and the trigger selection.
18.4.4.3
The on-chip ICE system supports nine trigger modes. The trigger modes are encoded as shown in
Table
FIFO. When the match condition is met, the appropriate flag AF or BF is set in DBGS register. Arming
the DBG module clears the AF, BF, and CF flags in the DBGS register. In all trigger modes except for the
event only modes change of flow addresses are stored in the FIFO. In the event only modes only the value
on the data bus at the trigger event B comparator match address will be stored.
18.4.4.3.1
In the A Only trigger mode, if the match condition for A is met, the AF flag in the DBGS register is set.
18.4.4.3.2
In the A Or B trigger mode, if the match condition for A or B is met, the corresponding flag(s) in the DBGS
register are set.
18.4.4.3.3
In the A Then B trigger mode, the match condition for A must be met before the match condition for B is
compared. When the match condition for A or B is met, the corresponding flag in the DBGS register is set.
18.4.4.3.4
In the Event Only B trigger mode, if the match condition for B is met, the BF flag in the DBGS register is
set. The Event Only B trigger mode is considered a begin-trigger type and the BEGIN bit in the DBGT
register is ignored.
18.4.4.3.5
In the A Then Event Only B trigger mode, the match condition for A must be met before the match
condition for B is compared. When the match condition for A or B is met, the corresponding flag in the
DBGS register is set. The A Then Event Only B trigger mode is considered a begin-trigger type and the
BEGIN bit in the DBGT register is ignored.
18.4.4.3.6
In the A And B trigger mode, Comparator A compares to the address bus and Comparator B compares to
the data bus. In the A and B trigger mode, if the match condition for A and B happen on the same bus cycle,
both the AF and BF flags in the DBGS register are set. If a match condition on only A or only B happens,
no flags are set.
For Breakpoint tagging operation with an end-trigger type trace, only matches from Comparator A will be
used to determine if the Breakpoint conditions are met and Comparator B matches will be ignored.
Freescale Semiconductor
18-17. The trigger mode is used as a qualifier for either starting or ending the storing of data in the
Trigger Modes
A Only
A Or B
A Then B
Event Only B
A Then Event Only B
A And B (Full Mode)
MC9S08DZ128 Series Data Sheet, Rev. 1
Chapter 18 Debug Module (S08DBGV3) (128K)
413